Mitsubishi Electric LT2-2250-B1T Instruction Manual Download Page 26

Page: 26 / 28

Installation of the solenoid arm

( 1 ) Install the rotary solenoid so that the gap

between the rotary solenoid and the solenoid
arm is about 0 to 0.5 mm.

Note: If the gap is too large, the roller and

the cam follower crank interfere while
rotating movement of the solenoid,
which causes malfunction and result in
failure of the thread trimmer device.

Removal procedure of the hook

( 1 ) Loosen three set screws of the small gear to

the hook shaft.

( 2 )  Remove the opener.
( 3 )  Remove the fixed knife.
( 4 )  Move the lever to the arrow direction,

and move the movable knife to the arrow
direction.

( 5 ) Remove the hook.
Note: To install the hook, reverse the removing

procedure.

HOW TO USE

Knife bracket

Movable knife

Hook

Opener

Fixed knife

Bobbin thread

holding spring

Lever

Cam follower

crank

Roller

Rotary solenoid

Solenoid arm

0 to 0.5 ㎜

— 23 —

Summary of Contents for LT2-2250-B1T





























Search results

Summary of Contents for LT2-2250-B1T

Reviews:

Related manuals for LT2-2250-B1T

Brands by name

Popular brands

Mitsubishi Electric LT2-2250-B1T, Instruction Manual

Search results

Summary of Contents for LT2-2250-B1T

Reviews:

Related manuals for LT2-2250-B1T

Brands by name

Popular brands