Mitsubishi Electric LT2-2250-B1T Instruction Manual Download Page 27

Page: 27 / 28

LT2-2250-B1T Specifications

Model

Specifications

LT2-2250-B1T

Application

Medium-heavy material

Max. sewing speed (rpm)

3,000

Stitch length (mm)

0 to 7

Needle bar stroke (mm)

33.4

Thread take-up lever stroke (mm)

68.0

Presser foot stroke (mm)

Hand

7.0

Knee

13.0

Needle

DP × 5 #18

Hook (horizontal rotating hook)

Large

Bobbin

Made of aluminum for thread trimmer

Lubrication system

Automatic lubrication

Thread trimmer method

Combination of fixed knife and movable knife

Touch back

○

Bed dimensions (mm)

517 × 178

Needle gauge (mm)

Standard 6.4
Special 3.2、4.8、8、9.5、12.7

Note: ● Feed dog, throat plate, rotating hook, bobbin case, bobbin, and bed slide should be those

designed for the thread trimmer.

● The bobbin should be of high quality free from deformation.

● Some materials, gauge sizes, and/or sewing conditions may require specifications other than

those listed above.

● These specifications are subject to change for machine improvement.

SPECIFICATIONS

— 24 —

Summary of Contents for LT2-2250-B1T





























Search results

Summary of Contents for LT2-2250-B1T

Reviews:

Related manuals for LT2-2250-B1T

Brands by name

Popular brands

Mitsubishi Electric LT2-2250-B1T, Instruction Manual

Search results

Summary of Contents for LT2-2250-B1T

Reviews:

Related manuals for LT2-2250-B1T

Brands by name

Popular brands