background image

5

Location Clearance 

Top

Open

Left

150mm

Right

150mm

Front

Open

Below

130mm

Installation conditions 

 Required space for installation 

Cautions

Be sure to secure at least the distances 

listed in the right-hand table from walls, 

flammable (combustible) materials and 

so on. 

Ensure a distance of at least 130mm from 

the floor. Failure to do so may result in dirt 

or water entering the appliance, causing 

damage. 

Ensure there is at least 150mm on 

both sides of the appliance to allow for 

maintenance. 

 Suitable walls

Flat walls with no unevenness. 

Walls that can support the weight of the appliance.

Reinforce any walls made with materials other than 

concrete. 

When installing on a concrete wall, use commercially 

available metal screw anchors.

 Making the appliance easier to use 

Refer to the "Installation position guide". 

Leave 200mm recommended clearance on the left to 

make maintenance easier. 

Avoid locations where people or doors might bump 

into the appliance. 

Installation position guide 

Wall

Right

Left 

150

150

130

Below

Unit (mm)

For men: 925mm

For women: 905mm

Summary of Contents for JT-SB216JSH2-H-NE
















Reviews: