Mitsubishi Electric FR-A8ND Instruction Manual Download Page 19 | Manualshive

Page: 19 / 104

background image

18

3

WIRING

3.1 Connection to network

(1) Be sure to check the following before connecting the inverter to the network.

• Check that the FR-A8ND is securely inserted into the inverter. (Refer to

• Check that the correct node address is set. (Refer to

.)

• Check that a drop cable is firmly connected to the FR-A8ND. (Refer to

(2) Make sure that the terminating resistor is installed at each end (between C+ and C-) of the trunk cable. These resistors

must meet the following requirements.

(3) Connect drop cables to the trank cable.

• If the trunk connector is a DeviceNet

sanctioned pluggable or sealed
connector, the connection to the active
network can be made at any time
whether the inverter is ON or OFF. The
option unit automatically detects when
the connection is completed.

• If connecting to the network with free

wires, power to the network and inverter
should be shut off as a safety
precaution in case two or more signal
wires are accidentally shorted together.

Requirements of terminating resistors

R (resistance value) = 121



1% metal film

0.25 W

Inverter

Trunk cable

Trunk connector

Drop cable

Terminating
resistor

Inverter

«
...
17
18
19
20
21
...
»

Summary of Contents for FR-A8ND









































































































Reviews:

No comments

Related manuals for FR-A8ND

Brand: B&B Electronics Pages: 73

Brand: B&B Electronics Pages: 4

Brand: ZIEHL-ABEGG Pages: 26

Brand: Potek Pages: 18

Brand: GMI Pages: 9

Brand: Transition Networks Pages: 13

Slimline Plus 1250

Brand: Wagan Pages: 32

Brand: HEIDENHAIN Pages: 44

Brand: PRO SIGNAL Pages: 2

Brand: Baumer Pages: 24

Factory-Link-SPE-M

Brand: I-novative Pages: 12

Brand: World Friendship Pages: 17

Indigo ADDEC-210

Brand: Crystal Vision Pages: 37

Brand: Parasound Pages: 7

Power Bank 1000

Brand: SunSynk Pages: 11

Brand: ETQ Pages: 32

Brand: Woodpecker Pages: 22

Brand: APT Pages: 43

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands