Mitsubishi Electric FR-A7NCA Instruction Manual Download Page 40

Page: 40 / 141

INVERTER SETTING

4.6

Inverter Reset

(1) Operation conditions of inverter reset

Which resetting method is allowed or not allowed in each operation mode is described below.

Inverter reset can be made any time.

Reset can be made only when the protective function of the inverter is activated.

Resetting Method

Operation Mode

Network

Operation

External

Operation

Reset from the
network

Inverter reset Index H2107

(Refer to page 94)

Allowed

Disallowed

Reset node service

(Refer to page 62)

Allowed

Disallowed

Error reset at inverter fault

(Refer to

page 33)

Pr.349

= 0

Allowed

Pr.349

= 1

Disallowed

Turn on the terminal RES-SD

Enabled

Switch off inverter power

Enabled

Reset from the
PU/DU

Inverter reset

Enabled

Reset at inverter fault

Enabled

CAUTION

1. When a communication line error has occurred, reset cannot be made from the network.

2. The inverter is set to the external operation mode if it has been reset in network operation mode in the

initial status.

To resume the network operation, the inverter must be switched to the network operation mode again.

Set a value other than "0" in

Pr. 340

to start in network operation mode.

(Refer to page 18.)

3. The inverter can not be controlled for about 1s after release of a reset command .

A7NCA.book 32 ページ２００６年７月３日　月曜日　午前９時４８分

Summary of Contents for FR-A7NCA














































































































































Search results

Summary of Contents for FR-A7NCA

Reviews:

Related manuals for FR-A7NCA

Brands by name

Popular brands

Mitsubishi Electric FR-A7NCA, Instruction Manual

Search results

Summary of Contents for FR-A7NCA

Reviews:

Related manuals for FR-A7NCA

Brands by name

Popular brands