Mitsubishi Electric apricot XEN-LS Installation Manual Download Page 5 | Manualshive

Page: 5 / 15

Mitsubishi Electric apricot XEN-LS Installation Manual Download Page 5

3

Installing an expansion card

The XEN-LS’s internal three-slot AT/ISA expansion card
cage can hold the following card configurations:

Slot

Maximum card size

top

three-quarter length (298 x 105 mm)

middle

full length (348 x 100 mm)

bottom

half length (160 x 100 mm)

Expansion cards

cannot be fitted while the cage is in the

computer; the cage must be removed, the card added to
the cage, then the cage refitted in the machine.

Expansion cards can also be fitted in an XP-i expansion
box which attaches to the side of the XEN-LS. Installation
instructions are contained in a guide that comes with the
XP-i box. Ask your Apricot supplier for details.

Installation

Do not remove the expansion card from its anti-static
wrapping until you are ready to install it. To install an
expansion card:

1.

Take suitable anti-static precautions as described in
the

XEN-LS Owner’s Handbook.

2.

Switch off the computer and disconnect it from the
AC power supply. Remove the system unit cover
and the expansion card cage as described in the
XEN-LS Owner’s Handbook.

3.

Place the card cage on a flat surface with the three
slots facing upwards.

4.

Remove one of the slot blanking plates by removing
its fastening screw. Be sure to choose a slot
compatible with the size of card you intend to fit.

«
...
3
4
5
6
7
...
»

Summary of Contents for apricot XEN-LS
















Reviews:

No comments