background image

18

MEM:  Memory Registers
The user can store and recall a combination of LO Frequency, Attenuation and Setup Title in
each of the sixty-four memory locations, 00 through 63.  Memory contents can be stored or
reviewed without setting the unit to the parameters indicated in the memory locations.

To store the settings in memory of the unit:

 

Press the “CURSOR” key to select the “MEM” field.

 

Press either arrow key until “STR” appears in the “MEM” field.

 

Press “ENT” to select the store function and the cursor will advance to the memory
register field.

 

Use the numeric data entry keys or the up and down arrow keys to select the memory
register (00 through 63) to be updated.  The contents of the memory location will be
displayed along with the memory register number.  Press “ENT” to select the memory
register field and the cursor will advance to the LO Frequency field.

 

Enter the LO Frequency to be stored in the memory location.

 

Press the “ENT” key and the cursor will advance to the Attenuation field. This will not
retune the unit. See note below.

 

Enter the Attenuation to be stored.

 

Press the “ENT” key and the cursor will advance to the Setup Title field.  This will not
retune the unit.  See note below.

 

Use the numeric data entry keys or the arrow keys to enter each character of the Setup
Title to be stored.  Use the “CURSOR” key to advance to the next character of the title.

 

Press “ENT” to store the entire combination of settings and the cursor will advance to the
“MEM” field.  See note below.

 

Press “ENT” again to set the unit to the displayed settings.

 

If “ENT” is not pressed after ten seconds, or “MENU” is pressed the “MEM” field will
become selected again and the display will be updated to reflect the actual settings.

Note:  If “ENT” is not pressed after 10 seconds the display will timeout and the actual setting
stored in the memory register will be displayed. If after 30 seconds “ENT” has not been pressed
the store function will be terminated.

To recall the settings from a memory register:

 

Press the “CURSOR” key to select the “MEM” field.

 

Press either arrow key until “RCL” appears in the “MEM” field.

 

Press “ENT” to select the recall function and the cursor will advance to the memory
register field.

 

Use the numeric data entry keys followed by “ENT” or the arrow keys to recall and view
the contents of a memory register (00 through 63) .

 

Press “ENT” to set the unit to the retrieved settings.

 

If “ENT” is not pressed after ten seconds, or “MENU” is pressed the “MEM” field will
become selected again and the display will be updated to reflect the actual settings.

Setup Title
Setup Title length may be up to twelve characters.  The range of allowable characters are ASCII
printable from 32 decimal (SP) to 122 decimal (z).

 

Use the numeric keypad to enter a numeric

digit directly.

To enter a title:

 

Press the “CURSOR” key to move the cursor to the Setup Title field.  Press an arrow key
or press and hold down the “CURSOR” key to select the first letter in the title field.

 

Use the up and down arrow keys or the numeric data entry keys to adjust the character in
this position.

 

Press the “CURSOR” key to advance to the next character position.

Summary of Contents for DNB-2B
























































Reviews: