background image

Warranty & Warning Information

12

Warranty Procedure 

To obtain service under this warranty, please return the item(s) in question to the point of purchase. 
All authorized distributors and dealers have a warranty program. Anyone returning goods to 
Mircom Technologies Ltd. must first obtain an authorization number. Mircom Technologies Ltd. will 
not accept any shipment whatsoever for which prior authorization has not been obtained. NOTE: 
Unless specific pre-authorization in writing is obtained from Mircom management, no credits will be 
issued for custom fabricated products or parts or for complete fire alarm system.  Mircom will at its 
sole option, repair or replace parts under warranty.  Advance replacements for such items must be 
purchased.

Note: Mircom Technologies Ltd.’s liability for failure to repair the product under this warranty after a 
reasonable number of attempts will be limited to a replacement of the product, as the exclusive 
remedy for breach of warranty.

Disclaimer of Warranties 

This warranty contains the entire warranty and shall be in lieu of any and all other warranties, 
whether expressed or implied (including all implied warranties of merchantability or fitness for a 
particular purpose) And of all other obligations or liabilities on the part of Mircom Technologies Ltd. 
neither assumes nor authorizes any other person purporting to act on its behalf to modify or to 
change this warranty, nor to assume for it any other warranty or liability concerning this product. 

This disclaimer of warranties and limited warranty are governed by the laws of the province of 
Ontario, Canada. 

Out of Warranty Repairs 

Mircom Technologies Ltd. will at its option repair or replace out-of-warranty products which are 
returned to its factory according to the following conditions. Anyone returning goods to Mircom 
Technologies Ltd. must first obtain an authorization number. Mircom Technologies Ltd. will not 
accept any shipment whatsoever for which prior authorization has not been obtained. 

Products which Mircom Technologies Ltd. determines to be repairable will be repaired and 
returned. A set fee which Mircom Technologies Ltd. has predetermined and which may be revised 
from time to time, will be charged for each unit repaired. 

Products which Mircom Technologies Ltd. determines not to be repairable will be replaced by the 
nearest equivalent product available at that time. The current market price of the replacement 
product will be charged for each replacement unit. 

WARNING: Mircom Technologies Ltd. recommends that the entire system be completely 
tested on a regular basis. However, despite frequent testing, and due to, but not limited to, 
criminal tampering or electrical disruption, it is possible for this product to fail to perform as 
expected. 

NOTE:  Under no circumstances shall Mircom Technologies Ltd. be liable for any special, 
incidental, or consequential damages based upon breach of warranty, breach of contract, 
negligence, strict liability, or any other legal theory. Such damages include, but are not 
limited to, loss of profits, loss of the product or any associated equipment, cost of capital, 
cost of substitute or replacement equipment, facilities or services, down time, purchaser’s 
time, the claims of third parties, including customers, and injury to property. 

MIRCOM MAKES NO WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR 
PURPOSE WITH RESPECT TO ITS GOODS DELIVERED, NOR IS THERE ANY OTHER 
WARRANTY, EXPRESSED OR IMPLIED, EXCEPT FOR THE WARRANTY CONTAINED 
HEREIN.

Summary of Contents for RA-1000 Series





















Reviews: