background image

Pre-installation inspections: 

1.  Verify that jumpers 

JP1

 and 

JP2 on the QDV-1000

 are over 

pins 2 and 3 for both

, that is the jumpers are in 

the 

left-most positions

 for both.  In case that the ‘Manual Message’ option is used, move JP2 over to pins 1 

and 2, which is the right-most position instead. 

2. Locate 

the 

J8 header

 on the QIF-5000B module; remove all jumper headers if any. 

3.  For a single stage system with voice recording to be played on the Evacuation channel 2, install the 

QDV-

0001 integrated circuit chip into socket U3 (this is the standard operation set up).

 

4.  For voice recording to be played on the Alert channel 3, install a QDV-0001 integrated circuit chip socket into 

U4. 

5.  For voice recording to be played on the Alert2 channel 4, install a QDV-0001 integrated circuit chip into socket 

U5.

 

J1

QDV-1000 DIGITIZED VOICE BOARD

PT1

PT2

PT3

PT4

PT5

JP1

J2

U4

U5

U6

U3

JP2

3  2  1

3  2  1

Evac.

Alert2 (Manual)

Alert

Background noise

Evac.  
Channel
2

Alert2
Channel
4

Alert
Channel 3

Header J1 connects to QDVP-100

TS1

TS1-2

TS1-1

MOVE JUMPER JP2 TO PINS 1 &2 IF ALERT 2
CHANNEL (MANUAL MESSAGE) IS USED.

Not Installed 
Not Used 

Paging 
Channel 1

LT-901 Rev.4 Aug 2006 

          Page 2 of 10 

Summary of Contents for QDV-1000













Reviews: