manualshive.com logo in svg

Miranda PresStation, User Manual

Share
Download
Miranda PresStation User Manual Download Page 114

PresStation User Manual 

Controlling a MVP 

Miranda Technologies Ltd 

Page 114 

13 Controlling a MVP 

t is possible to control either a Miranda Kaleido-K2 or Evertz multi-
video display processor (MVP).  This option allows the Presmaster to 
optionally switch layouts on the MVP each time that a channel is 

changed.  Additionally to this when using the Presmaster in conjunction with 
a Kaleido it is possible to setup one Kaleido to be a master so that changing a 
layout on the Kaleido will change a channel on the panel.   

 

Please note that the option to control an MVP is a software option and will 
not be available unless the appropriate licence is installed on the panel. 

Setting up control of a Miranda Kaleido 

One panel can control up to 16 Kaleidos over Ethernet.  One Kaleido can be 
used as a master to change channels on the panel when a layout is changed on 
the Kaleido. 

 

The setup of the Kaleido is carried out from the panel configuration file.  An 
example of the changes required to the panel configuration file is shown 
below.  

 

There will be one port entry for each Kaleido that will be controlled.  Start 
the port numbering from port256 and increment up by one for each Kaleido. 

 

Within the port section the device type and protocol must be as is shown.  
The ip="10.96.99.64" should be set to the ip address of the Kaleido and the 
net_port should always be set as is shown. 

 

If the Kaleido is to be a master, i.e. changing layout on the Kaleido will 
change channel displayed on the panel, then add the entry master=true.  It is 
important that only one Kaleido is set as a master.  If you do not want the 
Kaleido to be a master then leave this entry out. 

I 

Summary of Contents for PresStation


















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands