manualshive.com logo in svg

Miranda PresStation, User Manual

Share
Download
Miranda PresStation User Manual Download Page 104

Using Audio 

PresStation User Manual 

Page 104 

Miranda Technologies Ltd 

 
meter_profile2 
{ 
   pairname1 = "2" 
   pairname2 = "3" 
   pairname3 = "4" 
   pairname4 = "5" 
} 
meter_profile3 
{ 
   pairname1 = "6" 
   pairname2 = "2" 
   pairname3 = "6" 
   pairname4 = "2" 
} 
 

To access the audio buttons on the PresStation, press the “Out Gain” box on 
the display. The eight buttons at the bottom of the screen are the audio 
buttons referred to below. 

 

For this example pressing the audio 1 button will display: 

•

 

English 5.1 on the first 3 meter pairs. 

•

 

Spanish on the fourth meter pair. 

Pressing audio 2 button will display: 

•

 

Portuguese on the first meter pair 

•

 

German on the second meter pair 

•

 

Spanish on the third meter pair 

•

 

French on the last meter pair. 

Pressing audio 3 button will display 

•

 

Mono L on the first meter pair 

•

 

Portuguese on the second meter pair 

•

 

Mono L on the third meter pair 

•

 

Portuguese on the last meter pair 

 

Summary of Contents for PresStation


















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands