manualshive.com logo in svg

Miranda Kaleido-X, Installation Manual

Share
Download
Miranda Kaleido-X Installation Manual Download Page 32

26

Kaleido-X (4RU) Installation

Replacing a Defective Cooling Fan

3 Pull the assembly straight out of the frame by using the handle on the front of the fan 

module.

Once the defective fan has been replaced, reinstall the fan assembly

1 Position the assembly in the opening with the handle on the lower left, as shown 

below.

2 Slide the assembly into the opening and push on the handle to seat the connectors.

3 Tighten the two captive screws.

4 Power up the frame by plugging in the AC cords.

5 Verify that all eight fans are running properly.

In some cases there may be incidental contact between the screws holding 
the fans in place on the fan module and the edge of the card slot assembly. 
Pull firmly to remove the module.

Note:

In some cases there may be incidental contact between the screws 

holding the fans in place on the fan module and the edge of the card slot 
assembly. Push firmly to slide the assembly into place, easing up once the 
last row of screws is past the edge of the card slot assembly.

Captive screw

Cooling fan module

Handle

Captive screw

Summary of Contents for Kaleido-X












































Reviews:

No comments

Brands by name

Popular brands

Load more brands