manualshive.com logo in svg

Miranda Kaleido-X, Installation Manual

Share
Download
Miranda Kaleido-X Installation Manual Download Page 28

Front Card-Edge Connector

An ICAT connector is located on the front card edge at the bottom, below the RESET button. 
This connector is reserved for factory use, and has no user functionality.

KXI-16 Input Cards

The KXI-16HSV3 card is one of a series of input cards that can be installed in the Kaleido-X 
system. This card is a universal input card that accepts 3Gbps, HD-SDI, SD-SDI and 
composite inputs. Other cards in this series are the KXI-16HSV (3Gbps not supported), the 
KXI-16HS and KXI-16HS3 (composite inputs not supported), and the KXI-16SV (HD-SDI not 
supported).

Every KXI-16 card is complemented by a rear panel connector (KXI-16-R with 16 BNC 
connectors) that holds all input and output connectors associated with the card.

Input cards can be installed in any of the two available 

Input

 slots in the front of the 

Kaleido-X frame. These slots are color-coded GREEN on the front and rear panel of the 
frame.

Every input card is connected to the other cards in the Kaleido-X frame through the frame's 
internal midplane. External connections to a KXI-16 card are made through connectors 
mounted on the associated KXI-16-R rear panel. See 

Card Installation and Replacement

 on 

page 9, for instructions on installing the card and the rear panel.

Rear Panel Connections

The connectors located on the KXI-16-R rear panel are shown in the diagram and described 
in the table below.

Notes

• Be careful to install the KXI-16-R rear panel in the matching location at the 

rear of the frame.

• The  KXI-16  card  and  its  rear  panel can be installed in any order.
• Kaleido-X cards are hot-swappable; it is not necessary to turn off the 

Kaleido-X when installing or exchanging cards.

Summary of Contents for Kaleido-X












































Reviews:

No comments

Brands by name

Popular brands

Load more brands