manualshive.com logo in svg

Miranda Kaleido-X, Installation Manual

Share
Download
Miranda Kaleido-X Installation Manual Download Page 11

5

Kaleido-X (4RU)

Hardware Description & Installation Manual

The illustration above shows the location of the available slots in the frame. The function of 
each slot is given in the following table:

The rear of the frame holds the rear connector panels for the cards, the AC power 
connectors with integral ON/OFF switches, and a fan for power-supply cooling.

Monitoring the Temperature of the Kaleido-X

For optimal performance, it is strongly recommended that you operate the Kaleido-X in an 
environment with an ambient temperature lower than 20 ºC (68 ºF).

Slot

Function

Color code

Card type

1

Main

Grey

KXA-GPI-GEN

2

Output A

Yellow 

KXO-Dual3, KXO-Dual

3

Output B

4

Input A

Green

 

KXI-16HSV3, KXI-16HSV
KXI-16HS3, KXI-16HS
KXI-16SV

5

Input B

6

Option A

Mauve  

Future Use

7

Option B

IMPORTANT

When measuring the ambient room temperature, take your readings 
from directly in front of the Kaleido-X frame.

Slot #

5

Slot #

6

4

3

7

2

1

PSU A

PSU B

AC power sockets with 
ON/OFF switches

Power supply cooling fan

Rear connector panels

Summary of Contents for Kaleido-X












































Reviews:

No comments

Brands by name

Popular brands

Load more brands