MINOURA HYPERRIM Manual Download Page 1

- 1 -

MINOURA HyperRim Instruction Manual

Please read this instructions carefully before use.

• Read all instructions carefully before use.
• Some assembly required.
• Keep the manual handy at all times.  Lost instruction materials can be replaced
through Minoura or your local dealer.
• Do NOT use trainer for any other purpose than instructed.
• The trainer is manufactured to precise standards.  You may not disassemble or
rebuild it.
• "HyperRim" and "RDA" are trademarks of Minoura and may not be copied.

Thank you for

purchasing

Minoura's HyperRim

Trainer with RDA and our patented Hyper

Magturbo.

With its unique rim-drive system, the HyperRim is our most sophisti-

cated bicycle home trainer for both road and mountain bikes.  Minoura has long

been an innovator in stationary trainers, and our new HyperRim trainer continues that tradition.  The

Rim Drive Action (RDA) system has special drive pulleys that contact only the rim, avoiding wear and

tear to the tire and any unpleasant noise.  With the RDA system, training is smoother, more controlable,

and quieter.  Plus,  you avoid the cost of replacing worn-down tires.  The RDA system can handle

almost any bicycle with a wheel diameter of 26 to 28 inches and is the best trainer yet for mountain

bikes.

(This figure is
HyperRim type-D)

IMPORTANT NOTES

Summary of Contents for HYPERRIM













Reviews: