MINOLTA-QMS magicolor 330 Service Manual Download Page 97

Page: 97 / 132

magicolor 330 Large-Capacity Input Feeder Service Manual

LCIF-93

DRP 7.23 Tray Sensor Assembly (PL22.2.29)

Use this procedure to remove and replace the Tray Sensor Assembly for OPT1 Tray, OPT2 Tray, or OPT3 Tray
of the LCIF.

Removal

1. Remove the LCIF Drive Assembly (DRP 7.15).

2. Place the LCIF Drive Assembly on a flat and stable work surface.

3. Disconnect the P/J leading from the Tray Sensor Assembly.

4. Squeeze together the four latches securing the Tray Sensor Assembly to the LCIF Drive Assembly and

remove the Tray Sensor Assembly.

Replacement

1. Position the Tray Sensor Assembly against the cutout in the LCIF Drive Assembly.

2. Push the Assembly into the cutout.

The latches snap into place.

3. Reconnect the P/J leading from the Tray Sensor Assembly.

4. Reinstall the LCIF Drive Assembly (DRP 7.15).

Summary of Contents for magicolor 330





































































































































Search results

Summary of Contents for magicolor 330

Reviews:

Related manuals for magicolor 330

Brands by name

Popular brands

MINOLTA-QMS magicolor 330, Service Manual

Search results

Summary of Contents for magicolor 330

Reviews:

Related manuals for magicolor 330

Brands by name

Popular brands