background image

Dowel Drill

 Manual

     

30

LIMITED WARRANTY, 

DISCLAIMER 

Supplier warrants to Customer that the Services shall be provided in a workmanlike manner and 

that the Goods shall be free from defects in material and workmanship at the date of shipment 

from Supplier’s facility. This warranty shall not run to any person other than Customer. All claims 

under this warranty must be made in writing and delivered to Supplier prior to the expiration of 

one (1) year after the Goods have been delivered (or, if applicable, within one (1) year after the 

Services have been performed) or be forever barred.  Supplier will repair or replace Goods or 

parts recognized and acknowledged by Supplier as being defective at the time of delivery with-

out charge.  However, Supplier will bill Customer for Goods and/or Services not covered by the 

warranty, including travel expenses incurred while performing warranty service calls.  EQUIP-

MENT, COMPONENTS OR OTHER GOODS FURNISHED THAT ARE NOT MANUFACTURED 

BY SUPPLIER ARE ONLY COVERED TO THE EXTENT OF THE ORIGINAL MANUFACTURER’S 

WARRANTY, WHICH MAY VARY FROM THE ABOVE.  Further, the above warranty shall not 

apply to any hardware or software that has been repaired or altered without Supplier’s written 

permission by anyone other than Supplier’s personnel.  The foregoing states the sole and exclu-

sive remedy for any breach of warranty or for any other claim based on any defect in, or non-

performance of, the Goods or Services, whether based upon contract, warranty, negligence, 

tort (including strict liability) or otherwise.

NO EXPRESS WARRANTIES AND NO IMPLIED WARRANTIES, WHETHER OF MERCHANTABI-

LITY OR FITNESS FOR ANY PARTICULAR PURPOSE OR WEAR CAPACITY, OR OTHERWISE, 

SHALL APPLY TO THE GOODS AND SERVICES.  SUPPLIER SPECIFICALLY DISCLAIMS AND 

EXCLUDES ALL OTHER EXPRESS AND IMPLIED WARRANTIES.  NO WAIVER, ALTERATION, 

ADDITION OR MODIFICATION OF THE FOREGOING SHALL BE VALID UNLESS MADE IN 

WRITING AND SIGNED BY AN EXECUTIVE OFFICER OF SUPPLIER.  IN NO EVENT WILL SUP-

PLIER BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES.

WHAT IS NOT COVERED

 

This Limited Warranty does not cover any dam-

age, deterioration or malfunction resulting from 

normal wear or tear, or any alteration, modifica-

tion, improper or unreasonable use or mainte-

nance, misuse, abuse, accident, neglect, expo-

sure to excess moisture, fire, improper packing 

and shipping (such claims must be presented 

to the carrier), lightning, power surges, or other 

acts of nature.  This Limited Warranty does not 

cover any damage, deterioration or malfunction 

resulting from the installation or removal of this 

product from any installation, any unauthorized 

tampering with this product, any repairs at-

tempted by anyone unauthorized by Minnich 

to make such repairs, or any other cause which 

does not relate directly to a defect in materials 

and/or workmanship of this product.

WHO IS COVERED:

 

Only the original purchaser of this product 

is covered under this Limited Warranty.  This 

Limited Warranty is not transferable to sub-

sequent purchasers or owners of this prod-

uct.  The product must have been purchased 

directly from Minnich or from an authorized 

Minnich reseller.

WHAT IS COVERED

 

This limited warranty (“Limited Warranty”) 

covers manufacturing defects in materials 

and workmanship of a product.

Summary of Contents for A-1-36
































Reviews: