background image

2  |  minnkotamotors.com

©2020 Johnson Outdoors Marine Electronics, Inc.

NOTICE: 

Check with your Jack Plate or Outboard 

manufacturer to determine if additional hardware is 
needed to accommodate installing this bracket. Longer 
mounting bolts than originally provided by the outboard 
manufacturer may be needed for proper installation. 
Drilling holes may be required to accept the Jack Plate 
Bracket and may void your manufacturer’s warranty. Minn 
Kota is not responsible for damages that may result.

3

Outboard

Outboard

Transom

Transom

Complete Typical Installation

NOTICE: 

When mounting the Jack Plate Bracket to the Jack Plate it is recommended to review the additional mounting 

considerations for the complete installation of the Raptor. They can be found online a

minnkotamotors.com

 in the “Installation” 

section of the Raptor Owner’s Manual or Installation Instructions. They including how to mount the Hydraulic Pump and route the 
Hydraulic Hoses along with other recommendations.

NOTICE: 

If installing an additional bracket to the Jack 

Plate Bracket, keep the Red Retainer in place and follow 
the instructions included with the additional bracket. Do 
not install the 3” Setback Bracket before completing the 
installation of the Jack Plate Bracket to the Jack Plate. 

2.  Examine the Starboard side of your Jack Plate. Identify the 

holes to be used for installation, if your Jack Plate does not 
have pre-drilled holes ensure that you will not drill into any 
obstructions and that the hardware will be accessible  
for assembly. 

3.  The Raptor must have a clear, unobstructed path to  

operate. Check to make sure that your proposed location 
will allow the anchor to deploy and retract without hitting 
trim tabs, poling platforms, ladders, the engine or other 
obstructions. You should also consider your fishing methods 
when selecting the mounting location. Make sure that no 
interference exists between the Raptor and your engine 
during normal operation. With the location selected, trim 
the engine all the way up and all the way down, and steer 
the engine fully to the left and right to confirm proper 
engine clearance. Ensure there is a minimum of two to 
three inches of clearance from any point on the Raptor in 
all states of stow and deploy.

4.  The bottom edge of the Raptor should never be less than 

4” above the hull directly below the Raptor to prevent 
spray and drag conditions. This applies to any mounting 
configuration used. 

5.  Keep the Red Retainer on the Jack Plate Bracket in place 

during the installation until instructed to remove it. For all 
installations paired with an additional bracket, the Jack Plate 
Bracket must be installed prior to installing the Raptor or 
additional brackets. 

Raptor

Raptor

Raptor Range  

Raptor Range  

of Motion

of Motion

4

5

2"  

2"  

Minimum

Minimum

Hull directly 

Hull directly 

below Raptor

below Raptor

Outboard 

Outboard 

Motor  

Motor  

Range of  

Range of  

Motion

Motion

Bottom Edge 

Bottom Edge 

of Raptor

of Raptor

Red  

Red  

Retainer

Retainer

Jack Plate 

Jack Plate 

Bracket

Bracket

4"  

4"  

Minimum

Minimum

2"  

2"  

Minimum

Minimum

Starboard

2

6.  It may be necessary to remove a factory equipped E-ladder 

for proper bracket installation. Due to the wide variety of 
E-ladders, Minn Kota is not responsible for the re-installation or 
re-location of any factory equipped E-ladder.

7.  Bob’s Machine Shop Jack Plates require that holes be drilled 

to accept the Adapter Bracket. A spacer kit must be used to 
install correctly; see Minn Kota Spacer Block accessory Part 
#1810212 or equivalent from Bob’s Machine Shop.

Summary of Contents for 1810360



















Reviews: