Minitor SFIDA 01 Series Operation Manual Download Page 5

Page: 5 / 12

START/STOP Switch

This switch turns the motor ON or OFF.

START/STOP Lamp

This lamp lights up in accordance with the state of the motor.

MODE Switch

This switch changes the operation mode.

PANEL Mode Lamp

This lamp lights when it's in Panel Operation Mode.

REMOTE Mode Lamp
This lamp lights when it is in Remote Operation Mode.

(State of motor) (State of lamp)

During pauses                                        Red illuminates
During operation → Stop                             Red blinks
Operation at fixed speed of rotation                 Green illuminates
Operation outside fixed speed of rotation            Green blinks
Error number being displayed                         Orange blinks

Operating Procedure

5‑1 Type of Operation Mode

Four different modes are available ‑to switch mode press the MODE switch while the motor is
paused.The modes change in the following order:"Panel Operation Mode" "Panel/Remote Opera‑
tion Mode" and "Remote Operation Mode".When the power is turned on,it returns to the previ‑
ous operation mode.If the mode changes,all lamps on the operation panel will light up once.

●

Panel Operation Mode
This is operated by a switch on this operation panel.

●

Panel/Remote Operation Mode
The setting of the number of rotations is controlled from the operation panel, and other
operations are to be operated by the external signal from the CONTROL connector.

●

Remote Operation Mode

This is operated by an external signal from the CONTROL connector, and the mode can be
changed even if the device indicates an error number.

●

Selector Operation Mode

This is to be operated in the selector side after connecting the device and Selector
Pack (MT01SP) by the communication cable. Refer to the details of the Selector Pack
Operation Manual.

5‑2 Panel Operation Mode

1.Turn on the MAIN switch. "P.P." is displayed once in the Indicator.
Make sure that the PANEL mode lamp on the operation panel is lit.
2.Supply air to the motor. Control the amount of air pressure so that three lamps of LEVEL
Indicator are lighted and then adjust it in accordance with the exothermic heat condition

by details of the task.

Note: When the air pressure is too low, the first lamp of the LEVEL Indicator blinks;

3.Press the ROTATION switch so that the lamp of intended rotation direction lights up.
4.Press the ＋(UP) or −(DOWN) switch so that the intended speed of rotation is displayed
on the indicator.
5.Press the START/STOP switch to start or stop the motor.

5‑3 Panel/Remote Operation Mode

1.Turn on the MAIN switch. "P.E." is displayed once in the Indicator.
Make sure that operation PANEL and both REMOTE lamps of are lit.
2.Supply air to the motor. Refer to the details of "5‑2 Panel Operation Mode."

3.Turn the external ROTATION signal on or off so that LED of the intended rotation
  direction is lit. Complete the setup of the rotation direction 100ms before turning on
  the external START signal.
4.Press the ＋(UP) or −(DOWN) switch so that the intended speed of rotation is displayed
  on the indicator.
5. Switch the external START/STOP signal to turn the motor ON or OFF.
      (Operation of motor)      (External START signal)
            Stop                OFF (applied voltage 0V)

Start ON (applied voltage 12V〜24V)

5‑4 Remote Operation Mode

1.Turn on the MAIN switch. The indicator will display "E.E." once. Make sure that the
  REMOTE mode lamp on the operation panel is lit.
2.Supply air to the motor. Refer to the details of "5‑2 Panel Operation Mode."
3.Turn the external ROTATION signal on or off so that LED of the intended rotation
  direction is lit. Complete the setup of the rotation direction 100ms before turning on
  the external START signal.
4.Set up the external signal so that the number of rotations which are intended to set
  by the indicator may be shown.

・SPEED signal voltage range is DC 0V 〜12V.
・

Setting speed of rotation 60,000min‑1(max)/SPEED signal voltage is DC9V (±5%)/SPEED̲UD・SPEED̲PULSE signal.

5.Turn the external START/STOP signal ON or OFF to start or stop the motor.
The external signal to operate the motor is the same as "Panel/Report Operation Mode".

(Functioning of Memory)
If settings such as operation mode, rotation direction and the speed of rotation of motor
are changed, this data is recorded after the motor stops. When the MAIN switch is turned
on, the device can be operated in the previously set mode.

(Measures for resetting when malfunctions occur)
When malfunctions occur, the indicator displays an error number as "E. □"(□ is figures).
Push the RESET switch to reset. Since error "E.9" cannot be reset,turn off the MAIN
switch, fix the cause of the malfunction, and turn on the MAIN switch after about three
minutes.

*Please refer to "9‑2 When Malfunctions Are Detected".