background image

 

 

voltage/cell during constant 
current/constant voltage charging 
Default is 14.1V 

CHG_HYSTERESIS[V/cell] 

An over-voltage value 
(CHG_BULK_STOP_VOLTAGE 
+CHG_HYSTERESIS ) that it is allowed 
when charging. 
If one of the cells exceeds this value 
charging is immediately stopped. 
Default is 100mV/cell. 

CHG_START_VOLTAGE [V/cell] 

If cell voltage is below this value charging 
can be started. For PbSO4 battery this 
also sets the floating charge voltage.  
Default is 13.5V/cell 

CHG_IMIN [mA] 

If charge current in CV mode is less than 
this value 
PbSO4: enter maintenance mode and 
apply the float charge 
voltage(CHG_START_VOLTAGE) 
LiFePO4,LiPO: cut off the charge voltage 
Default is 290mA 

CHG_IFLOAT  

Charge current limit in float charge mode 
for PbSO4 batteries. 
Default is 100mA. 

CHG_GLOBAL_TOUT  

Global charge timeout. 
Default is 1260 minute. 

CHG_TOPPING_TIMER 

For Lithium based batteries after an 
overvoltage condition is detected for a cell 
a resting period is set by this timer before 
applying a small topping charge in case 
other cells are still not charged. 
Default is 1800s. 

CHG_TEMP_PCB[°C] 

Charge current is limited by 
CHG_ILIMIT_TEMP_PCB amount every 
30s,if board temperature exceeds this 
value. Can limit the charge current till 
CHG_IBULK/4 value. 
Defaults is 60°C. 

CHG_ILIMIT_TEMP_PCB [A] 

Limit charge current with this amount if 
board temperature exceeds 
CHG_TEMP_PCB. 
Default is 50mA. 

CHG_FREQUENCY[kHz] 

The working frequency of the charger 
buck-boost converter 
Default is 333kHz. 

CELLS[pcs] 

Number of configured cells to 
charge/balance 

Summary of Contents for Open-UPS












Reviews: