background image

 

 

Default is 5 sec. 

UPS_HARDOFF_TOUT[s] 

After UPS_VBAT_UVP_OFF_TOUT 
passed motherboard is signaled to shut 
down. The UPS will wait this period so 
that the Motherboard can shut down 
gracefully, than cut power and enter deep 
sleep. This period should not be too long 
to prevent battery drain. 
Default is 60 sec. 

UPS_SWITCHOVER_VBAT_TOUT[ms]  After UPS switches to battery, can switch 

back to Vin only after this time elapses. 
Default is 1000ms. 

UPS_SWITCHOVER_VIN_TOUT[ms]  

After UPS switches to input, can switch 
back to battery only after this time 
elapses. 
Default is 1ms. 

DCHG_IMAX[mA] 

Max allowed discharge current. In case 
discharge current exceeds this threshold 
shutdown will be initiated. 
Default is 10000 mA. 

CAPACITY[mAh] 

Battery Capacity. 
Default 7000mAh. 

CHG_BAT_TYPE 

The battery chemistry to be charged. 
0- PbSO4 (float charge is applied) 
1- LiFePO4 (float charge is not applied) 
2-LiPO(float charge is not applied) 
Other (float charge is not applied) 
Default is 0. 

CHG_VCOND[V] 

Conditioning/Pre-charge voltage. Charge 
current is limited to CHG_ICOND until cell 
voltage exceeds this value and for at least 
CHG_TCOND time . 
Default is 11.2V. 

CHG_ICOND[mA] 

Conditioning/Precharge current. Charge 
current is limited to this value until cell 
voltage exceeds CHG_VCOND value and 
for at least CHG_TCOND time . 
Default is 100mA. 

CHG_TCOND [s] 
  

Conditioning/Precharge time. Charge 
current is limited to  CHG_ICOND value 
until cell voltage exceeds CHG_VCOND 
value and it is applied during this time. 
Default is 30 sec. 

CHG_IBULK[mA] 

Fast charge current limit (constant current 
mode) 
Default is 1750mA. 

CHG_BULK_STOP_VOLTAGE[V/cell] 

Maximum allowed bulk charge 

Summary of Contents for Open-UPS












Reviews: