background image

2 Safety instructions

2.1 General notes

CAUTION

Warning of personal injury.

The product was in perfect condition with regard to safety features when it left the

factory.

To maintain this condition and to ensure safe operation, the user must follow the

instructions and observe the warnings in this manual.

2.2 Intended use

The remote display is intended for the display of the weight values of a scale and the

limited operation of a device. The unit is approved for operation in legal-for-trade

applications.
The remote displays PR 5110/60, ../70 are suitable for use in zones 1 (PR 5110/60, ../70)

and 21 (only PR 5110/70). The instruments are itted with an intrinsically safe serial

interface.
Product operation, commissioning and maintenance must be performed by trained and

qualiied personnel who are aware of and able to deal with the related hazards and take

suitable measures for self-protection.
The device relects the state of the art.
No warranty is given that the product is free of faults, especially not in conjunction with

third-party software and hardware components required for operation.
The manufacturer does not accept any liability for damage caused by third-party system

components or due to incorrect use of the product. The use of this product signiies

recognition of the stipulations listed above.

2.3 Initial inspection

Check the contents of the consignment for completeness. Check the contents visually to

determine whether any damage has occurred during transport. If there are grounds for

rejection of the goods, a claim must be iled with the carrier immediately. The

Minebea Intec sales or service organization must also be notiied.

2.4 Before operational startup

NOTICE

Perform visual inspection.

Before operational startup as well as after storage or transport, inspect the device

visually for signs of mechanical damage.
Before operational startup, acceptance of the installation by an authorized expert is

compulsory.

2 Safety instructions

Remote display PR 5110/60, ../70

EN-5

Minebea Intec

All manuals and user guides at all-guides.com

Summary of Contents for PR 5110/60





































Reviews: