Minebea Intec Contego Installation Manual Download Page 27 | Manualshive

Page: 27 / 44

background image

Type of assembly

H

without adapter plate

35 mm

with adapter plate

75 mm

3. Lift the vessel.
4. Make the drill holes for the threaded pins/stud screws (10).

5. It is indispensable to insert the threaded pins/stud screws (10) vertically with the

required height 'H'.

6. When using PR 6041/80S adapter plates: Place adapter plate (15) on the bottom (7)

within the outline marking (9).

7. When using PR 6041/80S adapter plates: Mount the adapter plate using screws (15).

Make sure to observe the tightening torque of the nuts (13) and the property classes

of the nuts (13) and washers (14), see Chapter

.

5 Installation

Hygienic Weighing Module Contego®

Minebea Intec

EN-25

«
...
25
26
27
28
29
...
»

Summary of Contents for Contego













































Reviews:

No comments

Related manuals for Contego

Brand: Acdeos Pages: 7

and Vantage Pro

Brand: DAVIS Pages: 4

and Vantage Pro

Brand: Davis Instruments Pages: 4

Brand: Datavideo Pages: 45

Brand: RaceChip Pages: 12

Brand: CAME Pages: 2

Brand: Groov-e Pages: 2

Brand: TrailFX Pages: 6

Brand: Fullwat Pages: 9

Brand: Trailboss Pages: 8

Brand: Duramaxx Pages: 44

Brand: Metra Electronics Pages: 20

Brand: Oben Pages: 12

Brand: VOLTCRAFT Pages: 84

Brand: Avanti Pages: 28

Mesh Helmet Cover

Brand: Ops-Core Pages: 2

Programmer DT20

Brand: Comfort audio Pages: 3

Brand: Lightolier Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands