Milwaukee MAX MW160 Instruction Manual Download Page 39

Page: 39 / 44

TROUBLESHOOTING

14. TROUBLESHOOTING

Symptom

Problem

Solution

Slow reponse /

Excessive drift

Dirty pH electrode

Soak the electrode tip in

MA9016

cleaning solution for 30 minutes

and then follow the Cleaning

procedure.

Reading fluctuates

up and down (noise)

Clogged/dirty junction.

Low electrolyte level

(refillable electrodes only)

Clean the electrode.

Refill with fresh

MA9012

electrolyte.

Display shows the

full scale value blinking

Reading out of range

Recalibrate the meter.

Check the sample is within

measurable range.

Check if electrolyte level and

general electrode status.

mV scale out of range

Dry membrane or dry

junction

Soak the electrode in

MA9015

storage solution for at least

30 minutes.

Display shows the

temperature unit blinking

Out of order temperature

probe

Replace the temperature probe.

Meter fails to calibrate or

gives faulty readings

Broken probe

Replace the probe.

LCD tags displayed

continuously at

startup

One of the keys is blocked

Check the keyboard.

If the error persists, contact

Milwaukee Technical Service.

“Er0, Er1, Er2” message

at start up

Internal error

Restart the meter.

If error persists, contact

Milwaukee Technical Service.

Summary of Contents for MAX MW160













































Search results

Summary of Contents for MAX MW160

Reviews:

Related manuals for MAX MW160

Brands by name

Popular brands

Milwaukee MAX MW160, Instruction Manual

Search results

Summary of Contents for MAX MW160

Reviews:

Related manuals for MAX MW160

Brands by name

Popular brands