Milwaukee MAX MW160 Instruction Manual Download Page 37

Page: 37 / 44

PC CONNECTION

13. PC CONNECTION

13.1. USING MI5200 PC APPLICATION

The logged data can be transferred to a PC via the Milwaukee Instruments

MI5200

Windows compatible application using the RS232 or USB serial interface.

The software is available for download at http://www.milwaukeeinst.com. Search for the

product code and click on it. After download is complete, use the exe file to install the

software.

MI5200

offers graphing and on-line help feature. Data can be exported to well-known

spreadsheet programs for further analysis.

1. Switch the meter off.

2. Connect the instrument to a PC with the supplied

MA9350

cable (if using the RS232

port) or with a standard USB cable.

3. Start the application.

Notes:

For RS232 other cables than MA9350 may use a different configuration and

communication between instrument and PC may not be possible.

Keep only one cable connected (RS232 or USB) during PC communication to avoid

possible errors.

13.2. SENDING COMMANDS FROM PC

It is also possible to remotely control the instrument with any terminal program.

1. Switch the meter off.

2. Use the

MA9350

cable to connect the instrument to a PC.

3. Start the terminal program and set the communication options as follows: 8, N, 1,

no flow control.

Command Types

To send a command to the instrument follow the next scheme:

<*> <command> <CR>

where: <*> is the command prefix,

<command> is the command code.

Note:

Either small or capital letters can be used.

Unit Change Command

CHU xx

Changes the instrument unit according with the parameter value (xx):

xx=01 pH range / 0.01 resolution

xx=03 mV / Rel mV range

xx=05 ppm range

Summary of Contents for MAX MW160













































Search results

Summary of Contents for MAX MW160

Reviews:

Related manuals for MAX MW160

Brands by name

Popular brands

Milwaukee MAX MW160, Instruction Manual

Search results

Summary of Contents for MAX MW160

Reviews:

Related manuals for MAX MW160

Brands by name

Popular brands