4
Accidental Submersion
If the tool gets submerged past the handle:
1. Retrieve the tool out of the water and immediately
remove the battery pack.
2.
drain for 24 hours before using again.
Storage
Never store with liquid inside the pump. To store
the tool:
1.
2. Remove the hose and battery pack.
WARNING
4.
NOTE:
The pump is not designed to sustain work-
ing in dry conditions. The pump will shutdown if
working in dry conditions for a long period of time.
5. Insert battery pack.
6. Turn on pump by turning the ON/OFF switch to
ON.
7. As soon as the pump begins to take in air or
NOTE:
8. Allow the liquid inside of the pump to drain out.
NOTE:
If anything but clear water is accidentally
30
seconds immediately after use.
9. Flush the pump with clear water immediately after
use to prevent any damage to the tool.
10.Remove the battery and hose from the pump. Let
pump and hose drain before storing.
OPERATION
WARNING
To reduce the risk of injury, always
wear proper eye protection marked
to comply with AS/NZS 1337.1
Fuel Gauge
To determine the amount of charge left in the battery,
turn the tool
ON
. The Fuel Gauge will light up for 2-3
seconds. When less than 10% of charge is left, 1 light
To signal the end of charge, 1 light on the fuel gauge
the battery pack.
If the battery becomes too hot, the fuel gauge lights
to cool down.
Operating the Pump
WARNING
-
plosive atmosphere. Do NOT pump
brine, laundry discharge, or any other application
which may contain caustic chemicals and/or
petrol, fuel oil, or kerosene.
This pump is designed for outdoor applications where
water and organic debris (sticks, leaves, sand, gravel
and soil) might be present. It can also be used with
-
wards to avoid damaging the tool.
1.
2. Connect the hose to the pump.
3. Lay out the hose to ensure there are no block-
ages, kinks or bends. Take appropriate safety
precuations to ensure the hose is secure for your
worksite.
Troubleshooting
Problem
Cause
Correction
Pump will
not run
Battery installed
when pump turned
on.
See "Removing/Installing
the HydroPass Filter.
Correct situation, then
turn pump off, then back
on to reset.
Flow rate is
too low
Hose is clogged or
damaged.
Flush the hose, or
replace the hose if
damaged.
Clean the HydroPass
Pump
shutdown
Dry pump shutdown. Correct situation, then
turn pump off, then back
on to reset.
Over
temperature
shutdown
Blocked hose line.
Hose line too high.
Hose line too long.
Pump ON for too long.
Correct situation, then
turn pump off, then back
on to reset.
Allow pump to cool.
Ensure the HydroPass filter is properly installed.
Do not operate without filter installed. Inspect the
filter and keep it clean and free of all foreign
objects.
WARNING
Place the HydroPass filter and lift tube below
water surface, aiming as near as possible to the
middle of the water source.
Do not submerge the tool past
the handle.
NOTE:
The pump will achieve best performance
with the HydroPass filter as flat as possible and
fully submerged in the water.
HydroPass filter is
not attached.
HydroPass filter is
clogged with debris.
unplug the charger and remove the
battery pack from the charger or tool before
performing any maintenance. Never disassemble
the tool, battery pack or charger. Contact a
MILWAUKEE
®
service facility for ALL repairs.
Maintaining Tool
Keep your tool, battery pack and charger in good
repair by adopting a regular maintenance program.
Inspect your tool for issues such as undue noise,
misalignment or binding of moving parts, breakage
of parts, or any other condition that may affect the
tool operation. Return the tool, battery pack, and
charger to a
MILWAUKEE
®
service facility for
repair. After six months to one year, depending on
use, return the tool, battery pack and charger to a
MILWAUKEE
®
service facility for inspection.
If the tool does not start or operate at full power with
a fully charged battery pack, clean the contacts on
the battery pack. If the tool still does not work
properly, return the tool, charger and battery pack,
to a
MILWAUKEE
®
service facility for repairs.
MAINTENANCE
WARNING
To reduce the risk of injury, always
Flush the HydroPass filter and lift tube with clear
water after use to prevent any damage to the
tool.
To reduce the risk of personal
injury and damage, never
immerse your tool, battery pack or charger in
liquid or allow a liquid to flow inside them.
