![background image](http://html1.mh-extra.com/html/milwaukee/heavy-duty-m12-ftb/heavy-duty-m12-ftb_original-instructions-manual_1799267009.webp)
17
16
ENGLISH
SYMBOLS
Please read the instructions carefully before starting
the machine.
CAUTION! WARNING! DANGER!
Remove the battery pack before starting any work on
the appliance.
Always wear goggles when using the machine.
Wear a suitable dust protection mask.
Wear gloves!
Accessory - Not included in standard equipment,
available as an accessory.
Do not dispose electric tools, batteries/rechargeable
batteries together with household waste material.
Electric tools and batteries that have reached the end
of their life must be collected separately and returned
to an environmentally compatible recycling facility.
Check with your local authority or retailer for recycling
advice and collection point.
n
Rated speed
V
Voltage
Direct Current
European Conformity Mark
British Conformity Mark
Ukraine Conformity Mark
EurAsian Conformity Mark
ENGLISH
Transporting Lithium Batteries
Lithium-ion batteries are subject to the Dangerous Goods Legislation
requirements.
Transportation of those batteries has to be done in accordance with
local, national and international provisions and regulations.
The user can transport the batteries by road without further
requirements.
Commercial transport of Lithium-Ion batteries by third parties is
subject to Dangerous Goods regulations. Transport preparation and
transport are exclusively to be carried out by appropriately trained
persons and the process has to be accompanied by corresponding
experts.
When transporting batteries:
Ensure that battery contact terminals are protected and insulated to
prevent short circuit.
Ensure that battery pack is secured against movement within
packaging. Do not transport batteries that are cracked or leak.
Check with forwarding company for further advice.
WORKING INSTRUCTIONS
Installing Accessories
1. Remove dust and debris from the collet body before inserting
accessory.
2. Insert the collet with the collet nut attached into the collet body.
Thread the collet nut onto the spindle but do not tighten it yet.
3. Clean the accessory mandrel, then insert it a minimum of 1" (25,4
mm) into the collet. The mandrel will overhang the collet and the
accessory about 1/2" (12,7 mm).
6
Collet
Mandrel
Overhang
about 1/2"
Insert mandrel
a minimum of 1" inside the collet
Accessory
ffi
ffi
ff
ff
ff
ff
Overhang about
1/2" (12,7 mm)
Insert mandrel a
minimum of
1
" (25,4 mm)
inside the collet
Collet
Mandrel
Accessory
4. Hold the spindle shaft steady with a 1/2" (12,7 mm) open end
wrench and securely tighten the collet nut with an 11/16" (17,5 mm)
open end wrench.
5. Reverse the procedure when removing the accessory.
WARNING! To reduce the risk of injury, always securely tighten
the collet to the grinders and clean mandrels before inserting
them into the collet. Otherwise the high-speed rotation of the
tool could force the accessory to fly out of the collet.
Operation
If you have just installed an accessory or are beginning a period of
work, test it by letting it spin for one minute before applying it to the
workpiece.
WARNING!
Never use an accessory that has been dropped. Out-of-
balance or damaged accessories can mar workpiece, damage the
tool, and cause stress that may cause accessory failure.
Use a clamp, vise or other practical means to hold your work.
Allow accessory to come to full speed before beginning work.
Control pressure and surface contact between accessory and
workpiece.
WARNING!
Never bang accessories onto work.Too
much pressure causes accessory failure or slows speed.
Make sure the tool comes to a complete stop before laying the tool
down.
If the tyre buffer begins vibrating, immediately stop the motor
and check to see if the accessory is dull. Dull accessories will
cause the tool to vibrate and could force the collet to fly off the
tool. Always replace or sharpen dull accessories.
Accessories are designed for specific uses. Only use points,
cones, plugs, grinding wheels and cut-off wheels for applications
for which they were designed. Follow manufacturer's care and use
instructions.
CLEANING
The ventilation slots of the machine must be kept clear at all times.
MAINTENANCE
Use only Milwaukee accessories and Milwaukee spare parts. Should
components need to be replaced which have not been described,
please contact one of our Milwaukee service agents (see our list of
guarantee/service addresses).
If needed, an exploded view of the tool can be ordered. Please
state the Article No. as well as the machine type printed on
the label and order the drawing at your local service agents or
directly at: Techtronic Industries GmbH, Max-Eyth-Straße 10,
71364 Winnenden, Germany.