background image

Part Number 550-110-738/1012

G SA

Gas-Fired Steam Boilers

Boiler Manual

  This manual must only be used by a 

qualified heating installer/service technician. Failure to comply could result in 

severe personal injury, death or substantial property damage.

  When  calling  or  writing  about  the  boiler—  Please  have:    •  boiler  model  number  from  the  boiler  rating  label    and    

•  CP number from the boiler jacket. You may list the CP number in the space provided on the “Installation and service 

certificate” found on page 20.

Contents 

Page

   1  Prepare boiler location .......................................................2
   2  Prepare boiler .....................................................................8
   3  Install piping .....................................................................11
   4  Install controls ..................................................................14
   5  Install gas piping ...............................................................15
   6  Field Wiring ......................................................................16
   7  Start-up ............................................................................17
   8  Checkout procedure .........................................................20
   9  Service and maintenance .................................................21
  10 Replacement parts ...........................................................26
 11  Dimensions .......................................................................30
 12  Ratings .............................................................................31

For Operating and Troubleshooting Instructions,  
see Spark Ignition Control Supplement

  Hazards that 

will or can cause minor personal 

injury or property damage.

  Special instructions on installation, operation or 

maintenance that are important but not related to 

personal injury or property damage.

 

INSTALLER 

 Read all instructions before install-

ing. 

Read page 2 first. Follow all instructions in 

proper order to prevent personal injury or death.

•  Consider piping and installation when determining 

boiler location.

•  Any  claims for damage or shortage in shipment 

must be filed immediately against the transporta-

tion company by the consignee.

•  GSA boilers cannot be adapted for heater use.

  Hazards that 

will cause severe personal injury, 

death or substantial property damage.

  Hazards that 

can cause severe personal injury, 

death or substantial property damage.

Hazard definitions

 

USER 

—  Please  read  the  following.  Failure  to 

comply could result in severe personal injury, 

death or substantial property damage.

• 

This document is for use only by your qualified 

heating installer/service technician.

•  Please see the User’s Information Manual for your 

reference.

•  Have  the  boiler  serviced  by  a  qualified  service 

technician, at least annually.

 

INSTALLER 

 

 

Spark ignition boilers — 

Refer to this manual 

for general installation and maintenance informa-

tion. Refer also to the GSA Spark Ignition Control 

Supplement, part number 550‑141‑971, for operat-

ing instructions, troubleshooting and other additional 

information  for  GSA  boilers  equipped  with  spark 

ignition.

Summary of Contents for GSA-075

































Reviews: