background image

14

15

 WARNING

To reduce the risk of injury, use only 
identical replacement parts recom-
mended by the manufacturer. Tool 
service must be performed only by 
qualifi ed repair personnel. Always 
wear safety goggles or glasses with 
side shields when servicing tools. 
Disconnect tool from air supply be-
fore servicing. 

Cleaning

Clean dust and debris from  tool vents. 
Keep tool handles clean, dry and free of oil 
or grease. Use only mild soap and a damp 
cloth to clean the tool, since certain cleaning 
agents and solvents are harmful to plastics 
and other parts. Some of these include gaso-
line, turpentine, lacquer thinner, paint thinner, 
chlorinated cleaning solvents, ammonia and 
household detergents containing ammonia. 
Never use fl ammable or combustible sol-
vents around tools.

 

MAINTENANCE

Cold Weather Operation

For cold weather operation, near and below 
freezing, the moisture in the air line may 
freeze and prevent tool operation. Use an 
air tool lubricant or permanent antifreeze as 
a cold weather lubricant in the air line. 

Do not store tools in a below-freezing envi-
ronment. Ice or frost could form on the tools' 
operating valves and mechanisms, causing 
tool failure.

Air Supply-Pressure and Volume

Air volume is as important as air pressure. 
The air volume supplied to the tool may be in-
adequate because of undersized fi ttings and 
hoses, or from the effects of dirt and water in 
the system. Restricted air fl ow will prevent 
the tool from receiving an adequate volume 
of air, even though the pressure reading is 
high. The results will be slow operation or 
reduced driving power. Before evaluating tool 
problems for these symptoms, trace the air 
supply from the tool to the supply source for 
restrictive connectors, low points containing 
water and anything else that would prevent 
full volume fl ow of air to the tool.

ACCESSORIES

For a complete listing of accessories refer to 
your

 MILWAUKEE 

Electric Tool catalog or go 

on-line to www.milwaukeetool.com. To obtain 
a catalog, contact your local distributor or a 
service center.

FIVE YEAR TOOL 

LIMITED WARRANTY

Use  MILWAUKEE fasteners with the 
following specifi cations:

Length: 0.375" to 1.5"
Collation Angle: 0°
Staple Crown Width: 1/4"

Quick Connectors 

Every 

MILWAUKEE

 tool is tested before leaving 

the factory and is warranted to be free from defects 
in material and workmanship.  

MILWAUKEE

 will 

repair or replace (at 

MILWAUKEE

’s discretion), 

without charge, any tool (including battery char-
gers) which examination proves to be defective 
in material or workmanship for fi ve (5) years after 
the date of purchase.  Return the tool and a copy 
of the purchase receipt or other proof of purchase 
to a 

MILWAUKEE

 Factory Service/Sales Support 

Branch location or 

MILWAUKEE

 Authorized 

Service Station, freight prepaid and insured.  This 
warranty does not cover damage from repairs 
made or attempted by other than 

MILWAUKEE

 

authorized personnel, misuse, alterations, abuse, 
normal wear and tear, lack of maintenance, or ac-
cidents.  Certain parts of certain tools, such as but 
not limited to o-rings, seals, bumpers, and driver 
blades for 

MILWAUKEE

 nailers and stapling tools, 

are considered normal wear and tear items not 
covered by this warranty.

The warranty period for Li-Ion Battery Packs is two 
(2) years from the date of purchase.  The warranty 
period for Ni-Cd Battery Packs, Flashlights, Radios, 
and Professional Hoists (lever, chain, and electric) 
is one (1) year from the date of purchase. 

 THE REPAIR AND REPLACEMENT REMEDIES 
DESCRIBED HEREIN ARE EXCLUSIVE.  IN NO 
EVENT SHALL 

MILWAUKEE

 BE LIABLE FOR ANY 

INCIDENTAL, SPECIAL, OR CONSEQUENTIAL 
DAMAGES OR FOR ANY EXPENSES, LOSSES 
OR DELAYS INCIDENTAL TO ANY DAMAGE TO, 
FAILURE OF, OR DEFECT IN ANY PRODUCT, 
INCLUDING BUT NOT LIMITED TO LOSS OF 
PROFITS.

THIS WARRANTY IS EXCLUSIVE AND IN LIEU 
OF ALL OTHER WARRANTIES, OR CONDITIONS, 
WRITTEN OR ORAL, EXPRESS OR IMPLIED.  
WITHOUT LIMITING THE GENERALITY OF 
THE FOREGOING, MILWAUKEE DISCLAIMS 
ANY IMPLIED WARRANTY OF MERCHANT-
ABILITY OR FITNESS FOR A PARTICULAR 
USE OR PURPOSE AND ALL OTHER IMPLIED 
WARRANTIES.  

This warranty gives you specifi c legal rights.  You 
may also have other rights that vary from state to 
state and province to province.  In those states that 
do not allow the exclusion of implied warranties or 
limitation of incidental or consequential damages, 
the above limitations or exclusions may not apply 
to you.  This warranty applies to the United States, 
Canada, and Mexico only.

 WARNING

Always disconnect the air supply 
from the tool and remove fastener 
strips  before changing or removing  
accessories. Only use accessories 
specifi cally recommended for this 
tool. Others may be hazardous.

Summary of Contents for 7155-21


























Reviews: