Milwaukee 6519 series, Operator'S Manuar

Page: 9 / 28

page 9
MAINTENANCE
Every MILWAUKEE tool is thoroughly inspected and tested before leav-
ing our manufacturing facilities. Should any trouble develop, return the
complete tool prepaid to our Corporate Office, Branch Office/Service
Center or nearest Authorized MILWAUKEE Service Station. If inspection
shows the trouble is caused by defective workmanship or material, all
repairs will be made without charge, and the tool will be returned, trans-
portation prepaid. Battery packs for cordless tools are warranted for one
year from the date of purchase.
This warranty does not apply where: (1) repairs or attempted repairs have
been made by persons other than MILWAUKEE personnel or Authorized
Service Station personnel; (2) repairs are required because of normal
wear; (3) the tool has been abused or involved in an accident; (4) misuse
is evident, such as caused by overloading the tool beyond its rated ca-
pacity; (5) the tool has been used after partial failure or (6) the tool has
been used with an improper accessory. No other warranty, written or ver-
bal, is authorized.
For a complete listing of accessories refer to your MILWAUKEE Electric
Tool catalog. To obtain a catalog, contact your local distributor or a
service center listed on the back cover of this operator’s manual.
Quik-Lok
®
Cord Sets
8' Quik-Lok
®
Cord
Catalog No. 48-76-4008
25' Quik-Lok
®
Cord
Catalog No. 48-76-4025
Offset Blade Adapter (Fig. 7)
Select Models
Catalog No. 48-03-2005
An offset blade adapter is available to make flush cuts possible. To at-
tach, remove blade clamping screw and blade clamp. Place adapter over
spindle, lining up hole in adapter casting with threaded hole in spindle.
Replace screw, attaching adapter to spindle. Blade can then be secured
in adapter blade clamp in the same manner it was secured in the spindle
clamp.
ACCESSORIES
Select Models:
Blade Clamp
Catalog No. 42-68-0676
Blade Clamp Screw
Catalog No. 06-83-2971
“787” Blades:
Blade Clamp
Catalog No. 42-68-0681
Blade Clamp Screw
Catalog No. 06-83-2971
See Pages 23, 24 & 25 for a listing of Super Sawzall
®
Blades.
Fig. 7
Maintaining Tools
Keep your tool in good repair by adopting a regular maintenance pro-
gram. Before use, examine the general condition of your tool. Inspect
guards, switches, tool cord set and extension cord for damage. Check for
loose screws, misalignment, binding of moving parts, improper mount-
ing, broken parts and any other condition that may affect its safe opera-
tion. If abnormal noise or vibration occurs, turn the tool off immediately
and have the problem corrected before further use. Do not use a
damaged tool. Tag damaged tools “DO NOT USE” until repaired
(see “Repairs”).
Under normal conditions, relubrication is not necessary until the motor
brushes need to be replaced. After six months to one year, depending on
use, return your tool to the nearest MILWAUKEE service facility for the
following:
•
Lubrication
• Brush inspection and replacement
• Mechanical inspection and cleaning (gears, spindles, bearings,
housing, etc.)
• Electrical inspection (switch, cord, armature, etc.)
• Testing to assure proper mechanical and electrical operation
Cleaning
Clean dust and debris from vents. Keep the tool handles clean, dry and
free of oil or grease. Use only mild soap and a damp cloth to clean your
tool since certain cleaning agents and solvents are harmful to plastics
and other insulated parts. Some of these include: gasoline, turpentine,
lacquer thinner, paint thinner, chlorinated cleaning solvents, ammonia and
household detergents containing ammonia. Never use flammable or com-
bustible solvents around tools.
Repairs
If your tool is damaged, return the entire tool to the nearest service center
listed on the back cover of this operator’s manual.
To reduce the risk of injury, electric shock and
damage to the tool, never immerse your tool in liquid
or allow a liquid to flow inside the tool.
WARNING!
WARRANTY
To reduce the risk of injury, always unplug your tool
before performing any maintenance. Never
disassemble the tool or try to do any rewiring on the
tool's electrical system. Contact a MILWAUKEE
service facility for ALL repairs.
WARNING!