4
5
2.
To
vary
the speed, increase or decrease the pres-
sure on the trigger. The further the trigger is pulled,
the greater the speed.
3.
To
stop
the tool, release the trigger. Ensure the
tool has come to a complete stop before laying
the tool down.
Installing Bits and Sockets
Always remove the battery before inserting or remov-
ing accessories. Select the proper style and size
accessories for the job. This driver is intended for
use with drill and driver bits with a 1/4" hex shank
and ball detent recess.
1.
To
install
the accessory, pull out the collar and
insert the accessory. Release the collar.
2.
To
remove
the accessory, pull out the collar and
remove the accessory.
Setting the Mode
The mode selector collar can be set to
60
Tightening
80
Tightening
80
Drilling
60 in. lbs, 80 in. lbs, or Drill. When
properly adjusted, the clutch will slip at
the set torque to prevent over-tighten-
ing and possibly damaging the bands.
To tighten bands, turn the mode selec-
tor collar so the arrow lines up with
either 60 or 80, as indicated by the
band manufacterer.
To drill, turn the mode selector collar
so the arrow lines up with
.
Torque LED
When the specified torque is reached (60/80 in.lbs),
the Torque LED on the back of the tool will light.
Calibration
To maintain high-precision torque, the tool will occa-
sionally need to be checked for calibration. To signify
that the tool may be out of an acceptable tolerance
torque range, the Torque LED will flash after the trig
-
ger is released. The tool can continue to be used for
jobs not requiring accurate torque, but should be re
-
turned to a MILWAUKEE service facility before using
for precision torque work. Call 1-800-SAWDUST for
a service facility near you. MILWAUKEE will return to
you a fully calibrated tool, along with a manufacturer's
Certificate of Compliance.
Battery Pack Protection
To protect the battery from damage and extend its
life, the tool’s intelligent circuit monitors current draw,
temperature, and voltage drops.
In extremely high torque, binding, stalling, and short
circuit situations that cause high current draw, the
fuel gauge will flash, and the tool will turn OFF. To
reset, release the trigger.
Under extreme circumstances, the internal tem-
perature of the battery could become too high. If this
happens, the fuel gauge will flash and the battery
pack will shut off. Let the battery pack cool and then
continue work.
This tool provides a quick, convenient means of drill-
ing small holes and installing and removing bands.
APPLICATIONS
WARNING
To reduce the risk of electric shock,
check work area for hidden pipes
and wires before drilling or driving screws.
Drilling in Wood, Composition Materials
and Plastic
Always use sharp bits. When using twist drill bits, pull
the bit out of the hole frequently to clear chips from
the bit flutes. To reduce the chance of splintering,
back work with a piece of scrap wood.
During binding or high torque drilling applications,
the tool may shut down. To reset, release the trigger.
Tightening/Removing Bands
Adjust the clutch to the proper setting as indicated by
the band manufacterer. Place the proper size socket
into the tool. Fit the socket over the band fastener and
pull the trigger. When the proper torque is reqched,
the clutch will slip, the tool will stop, and the torque
LED will light. Release the trigger.
When removing bands, it may be necessary to
slightly loosen the band fastener by hand before
using the tool's reverse. Fit the socket over the band
fastener. Manually rotate the tool counterclockwise to
release the torque on the fastener. Put the tool into
reverse and pull the trigger fo fully release the band.
MAINTENANCE
WARNING
To reduce the risk of injury, always
unplug the charger and remove the
battery pack from the charger or tool before
performing any maintenance. Never disassemble
the tool, battery pack or charger. Contact a
MILWAUKEE service facility for ALL repairs.
Maintaining Tool
Keep your tool, battery pack and charger in good
repair by adopting a regular maintenance program.
Inspect your tool for issues such as undue noise,
misalignment or binding of moving parts, breakage of
parts, or any other condition that may affect the tool
operation. Return the tool, battery pack, and charger
to a MILWAUKEE service facility for repair. After six
months to one year, depending on use, return the
tool, battery pack and charger to a MILWAUKEE
service facility for inspection.
If the tool does not start or operate at full power with
a fully charged battery pack, clean the contacts on
the battery pack. If the tool still does not work prop
-
erly, return the tool, charger and battery pack, to a
MILWAUKEE service facility for repairs.
WARNING
To reduce the risk of personal in-
jury and damage, never immerse
your tool, battery pack or charger in liquid or
allow a liquid to flow inside them.
Cleaning
Clean dust and debris from any vents. Keep tool
clean, dry and free of oil or grease. Use only mild
soap and a damp cloth to clean, since certain clean-
ing agents and solvents are harmful to plastics and
other insulated parts. Some of these include gasoline,
turpentine, lacquer thinner, paint thinner, chlorinated
cleaning solvents, ammonia and household deter-
gents containing ammonia. Never use flammable or
combustible solvents around tools.
Repairs
For repairs, return the tool, battery pack and charger
to the nearest authorized service center.
ASSEMBLY
WARNING
Recharge only with the charger
specified for the battery. For spe
-
cific charging instructions, read the operator’s
manual supplied with your charger and battery.
Removing/Inserting the Battery
To
remove
the battery, push in the release buttons
and pull the battery pack away from the tool.
WARNING
Always lock the trigger or remove
the battery pack any time the tool
is not in use.
To
insert
the battery, slide the pack into the body
of the tool. Make sure it latches securely into place.
OPERATION
WARNING
To reduce the risk of injury, always
wear proper eye protection marked
to comply with ANSI Z87.1.
When working in dusty situations, wear appro-
priate respiratory protection or use an OSHA
compliant dust extraction solution.
Always remove battery pack before changing
or removing accessories. Only use accessories
specifically recommended for this tool. Others
may be hazardous.
Fuel Gauge
To determine the amount of charge left in the battery,
turn the tool
ON
. The Fuel Gauge will light up for 2-3
seconds. When less than 10% of charge is left, 1 light
on the fuel gauge will flash 4 times.
To signal the end of charge, 1 light on the fuel gauge
will flash 8 times and the tool will not run. Charge
the battery pack.
If the battery becomes too hot, the fuel gauge lights
will flash and the tool will not run. Allow the battery
to cool down.
Using the Control Switch
The control switch may be set to three positions:
forward, reverse and lock. A
lways allow the motor
to come to a complete stop before using the control
switch to avoid damage to the tool.
LOCK
Push to CENTER
Reverse
Forward
1.
For
forward
(clockwise) rotation, push in the con-
trol switch from the right side of the tool.
Check
the direction of rotation before use.
2.
For
reverse
(counterclockwise) rotation, push in
the control switch from the left side of the tool.
Check direction of rotation before use.
3.
To
lock
the trigger, push the control switch to the
center position. The trigger will not work while
the control switch
is in the center locked position.
Always lock the trigger or remove the battery pack
any time the tool is not in use.
Starting, Stopping and Controlling Speed
1.
To
start
the tool, grasp the handle(s) firmly and
pull the trigger.
NOTE:
An LED is turned on when the trigger is
pulled and will go off shortly after the trigger is
released.
ACCESSORIES
WARNING
Use only recommended accesso-
ries. Others may be hazardous.
For a complete listing of accessories, go online to
www.milwaukeetool.com or contact a distributor.
SERVICE - UNITED STATES
1-800-SAWDUST
(1.800.729.3878)
Monday-Friday, 7:00 AM - 6:30 PM CST
or visit
www.milwaukeetool.com
Contact Corporate After Sales Service Technical
Support with technical, service/repair, or warranty
questions.
Email: [email protected]
Become a Heavy Duty Club Member at
www.milwaukeetool.com to receive important
notifications regarding your tool purchases.
SERVICE - CANADA
Milwaukee Tool (Canada) Ltd
1.800.268.4015
Monday-Friday, 7:00 AM - 4:30 PM CST
or visit
www.milwaukeetool.ca
LIMITED WARRANTY
USA & CANADA
Every MILWAUKEE power tool* (see exceptions below) is warranted
to the original purchaser only to be free from defects in material and
workmanship. Subject to certain exceptions, MILWAUKEE will repair
or replace any part on an electric power tool which, after examination,
is determined by MILWAUKEE to be defective in material or workman-
ship for a period of five (5) years** after the date of purchase unless
otherwise noted. Return of the power tool to a MILWAUKEE factory
Service Center location or MILWAUKEE Authorized Service Station,
freight prepaid and insured, is required. A copy of the proof of purchase
should be included with the return product. This warranty does not
apply to damage that MILWAUKEE determines to be from repairs
made or attempted by anyone other than MILWAUKEE authorized
personnel, misuse, alterations, abuse, normal wear and tear, lack of
maintenance, or accidents.
Normal Wear: Many power tools need periodic parts replacement and
service to achieve best performance. This warranty does not cover
repair when normal use has exhausted the life of a part including,
but not limited to, chucks, brushes, cords, saw shoes, blade clamps,
o-rings, seals, bumpers, driver blades, pistons, strikers, lifters, and
bumper cover washers.
*This warranty does not cover Air Nailers & Staplers; Airless Paint
Sprayer; Cordless Battery Packs; Gasoline Driven Portable Power
Generators; Hand Tools; Hoist – Electric, Lever & Hand Chain;
M12™ Heated Gear; Reconditioned Product; and Test & Measure-
ment Products. There are separate and distinct warranties available
for these products.
**The warrant
y period for Job Site Radios, M12™ Power Port, M18™
Power Source, Jobsite Fan and Trade Titan™ Industrial Work Carts
is one (1) year from the date of purchase. The warranty period for
the
M18 FUEL™ 1" D-Handle High Torque Impact Wrenches, Drain
Cleaning Cables, AIRSNAKE™ Drain Cleaning Air Gun Accessories,
REDLITHIUM™ USB Laser Levels and TRAPSNAKE™ 25' Auger
w/ CABLE DRIVE™ is two (2) years from the date of purchase. The
warranty period for the M18™ Compact Heat Gun, 8 Gallon Dust Ex
-
tractor, M18™ Framing Nailers, M18 FUEL™ 1/2" Ext. Anvil Controlled
Torque Impact Wrench w/ ONE-KEY™, M18 FUEL™ 1" High Torque
Impact Wrench w/ ONE-KEY™, M18 FUEL™ 2 Gal. Compact Quiet
Compressor, M12™ Laser Levels, 165' Laser Detector, M12™ 23GA
Pin Nailer, M18 FUEL™ 1/4" Blind Rivet Tool w/ ONE-KEY™, M12
FUEL™ Low Speed Tire Buffer, and the M18 FUEL™ Dual Action
Random Orbital Polishers is three (3) years from the date of purchase.
The warranty period for the LED in the LED Work Light and the LED
Upgrade Bulb for the Work Light is the lifetime of the product subject
to the limitations above. If during normal use the LED or LED Bulb
fails, the part will be replaced free of charge.
Warranty Registration is not necessary to obtain the applicable war-
ranty on a MILWAUKEE power tool product. The manufacturing date
of the product will be used to determine the warranty period if no proof
of purchase is provided at the time warranty service is requested.
