manualshive.com logo in svg

Milnor 68036M5K, Installation And Service

Share
Download
Milnor 68036M5K Installation And Service Download Page 48

 

 

 

 

 

PELLERIN MILNOR CORPORATION

 

•  Install safety stands before performing maintenance under a tilted machine. 

•  NEVER test or operate (manually or automatically) any machine function with any 

portion of a person's body under the tilted machine - even if the safety stands are installed. 

 

 

WARNING  6 : Crush/Sever hazard

—Tilt machines with tilt wheels/cradles may lunge 

forward or rearward and even fall over if the non-tilted ends are raised out of their cradles - 
killing/injuring personnel and/or damaging property. 

•  NEVER manually tilt (lift) both ends of the machine at the same time. One end must 

always be seated in its cradle. 

•  ALWAYS visually inspect the tilt wheels to be sure they are all fully seated in their 

cradles before each manual tilt up. 

•  Pneumatic valve manual operation must be done by trained competent maintenance 

personnel who thoroughly understand the system and all the consequences of manual 
operations. 

•  ALWAYS understand beforehand all the consequences of manually operating pneumatic 

valves.  

•  NEVER permit operation with malfunctioning tilt limit switches 

 

Tilting machines leave the factory with 4 hold-down bolts (two per side) locking the tilting mid-
frame to the floor frame (

Figure 7

). Remove these bolts after machine is anchored and grouted, 

service connections are complete and all other installation steps are complete. 

Figure 6: Safety stand in place 

 

Figure 7: Tilting Mid Frame to Floor Locking Bolts 

 

  

 

 

  

 

— End of BIIFLI01 — 

 

44

Summary of Contents for 68036M5K


























































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands