Milnor 68036M5K Installation And Service Download Page 23

Page: 23 / 185

Detail: Stand Placement

Detail: Stand base mounting

hole pattern

Receiver

Mirror

Stand

Emitter

INSTALLATION:

Position the stands as shown in the detail. The poles
are to be exactly parallel to each other and truly
vertical.

IMPORTANT: The midpoint of the mirrors must be
directly in line within the midpoint of the sensor’s
defined area. The upper and lower limits of the
defined area are dimensioned in the light screen
instruction manual supplied with parts.

Midpoint

Receiver

Emitter

Mirror

Mirror Alignment

Mounting

hardware

(not supplied)

Pole
leveling
bolts -
4 places
(supplied)

Base
leveling
bolts
4 places
(supplied)

Post
level
(supplied)

Leveling

Figure 2: Safety Light Screen Installation

48040M7K, 68036M5K, 72046M5K

Page (2 / 3)

BMP150061/2016046A

Safety Light Screen Components & Installation

Summary of Contents for 68036M5K


























































































































































































Search results

Summary of Contents for 68036M5K

Reviews:

Brands by name

Popular brands

Milnor 68036M5K, Installation And Service

Search results

Summary of Contents for 68036M5K

Reviews:

Brands by name

Popular brands