ENGLISH
OM-363 Page 23
B. For 350 LX Models
All values in both tables were calculated at 60% duty cycle.
Actual input voltage cannot exceed
±
10% of indicated required input voltage shown in both tables. If actual input voltage is outside of this range,
damage to unit may occur.
Failure to follow these electrical service guide recommendations could create an electric shock or fire hazard. These recommenda-
tions are for a dedicated branch circuit sized for the rated output and duty cycle of the welding power source.
50/60 Hertz Models
Without Power Factor Correction
Input Voltage
200
220
230
400
440
460
520
575
Input Amperes At Rated Output*
125
103
110
57
52
55
43
42
Max Recommended Standard Fuse Or Circuit Breaker
Rating In Amperes
Circuit Breaker
1
Time-Delay Fuse
2
150
125
125
70
70
60
60
50
Normal Operating (Fast) Fuse
3
175
175
175
90
90
80
70
70
Min Input Conductor Size In AWG
4
3
3
4
8
8
8
8
8
Max Recommended Input Conductor Length In
Feet (Meters)
151
(46)
182
(56)
171
(52)
246
(75)
298
(91)
326
(99)
416
(127)
509
(155)
Min Grounding Conductor Size In AWG
4
6
6
6
8
8
8
8
8
*
Input amperes at rated output is the amperage draw for that particular input voltage if the machine is run at its rated welding
output (see Section 3-5 for rated welding output).
Reference: 2005 National Electrical Code (NEC)
1 If a circuit breaker is used in place of a fuse, choose a circuit breaker with time-current curves comparable to the recommended fuse.
2 “Time-Delay” fuses are UL class “RK5” .
3 “Normal Operating” (fast) fuses are UL class “K5” (up to and including 60 amp), and UL class “H” ( 65 amp and above).
4 Conductor data in this section specifies conductor size (excluding flexible cord or cable) between the panelboard and the equipment per NEC Table
310.16. If a flexible cord or cable is used, minimum conductor size may increase. See NEC Table 400.5(A) for flexible cord and cable requirements.
Failure to follow these electrical service guide recommendations could create an electric shock or fire hazard. These recommenda-
tions are for a dedicated branch circuit sized for the rated output and duty cycle of the welding power source.
50/60 Hertz Models
With Power Factor Correction
Input Voltage
200
220
230
400
440
460
520
575
Input Amperes At Rated Output*
92
77
78
40
39
38
33
31
Max Recommended Standard Fuse Or Circuit Breaker
Rating In Amperes
Circuit Breaker
1
Time-Delay Fuse
2
110
100
90
50
50
45
40
35
Normal Operating (Fast) Fuse
3
125
125
125
70
60
60
50
45
Min Input Conductor Size In AWG
4
4
6
6
8
8
8
10
10
Max Recommended Input Conductor Length In
Feet (Meters)
145
(44)
119
(36)
130
(40)
263
(80)
318
(97)
347
(106)
300
(91)
367
(112)
Min Grounding Conductor Size In AWG
4
6
6
6
8
10
10
10
10
*
Input amperes at rated output is the amperage draw for that particular input voltage if the machine is run at its rated welding
output (see Section 3-5 for rated welding output).
Reference: 2005 National Electrical Code (NEC)
1 If a circuit breaker is used in place of a fuse, choose a circuit breaker with time-current curves comparable to the recommended fuse.
2 “Time-Delay” fuses are UL class “RK5” .
3 “Normal Operating” (fast) fuses are UL class “K5” (up to and including 60 amp), and UL class “H” ( 65 amp and above).
4 Conductor data in this section specifies conductor size (excluding flexible cord or cable) between the panelboard and the equipment per NEC Table
310.16. If a flexible cord or cable is used, minimum conductor size may increase. See NEC Table 400.5(A) for flexible cord and cable requirements.
Summary of Contents for Syncrowave 250 DX
