background image

Operator's Manual:  Millcreek 57G & 77G Ground Drive Spreaders

3-2

Operating the Spreader

WARNING!  Before proceeding with operation of the spreader, review all safety
statements as provided in Section 1 of this manual.

WARNING: 

 To prevent serious personal injury, ensure that ALL safety shields are in place on the

spreader before starting operation.  NEVER operate the spreader without ALL safety shields in place.

ATTENTION: 

 In order to obtain proper, aggressive spreading action, 

the spreader ground speed must

reach a minimum of 3.0 miles per hour--the equivalent of a comfortable walking pace.  

(Note that the

wheels drive the beater action.)  However, spreading at speeds over 6.0 miles per hour (i.e. similar to a very
brisk walking pace) can cause excessive wear or damage to the equipment.

ATTENTION: 

 Verify that the 

spreader operating lever has been set to the proper length 

for easy

operator access and minimum five (5) inch clearance from the rear of the tractor chassis.  Refer to 

Section 2

 for

adjustment instructions, if needed.  Failure to properly adjust the lever may result in damage to the spreader
during operation.

1.

Ensure that the spreader (and tractor) are not in motion (in a stopped position).

2.

If you have a spreader with the endgate option, lift the endgate.

3.

To engage the apron chain for spreading action, push DOWN on the operating lever.

4.

Ensure that you are reaching the optimal operating speed for spreading (at least 3.0 mph, but not
more than 6.0 mph).  Remember that this optimal speed is similar to a comfortable walking pace.

5.

When the spreader box is completely unloaded, disengage the apron chain drive by pulling UP the
operating lever.

6.

Refer to Section 4 in this manual for maintenance to be performed following operation of the spreader.

IMPORTANT!  After a few hours of initial operation, watch and listen for any loose components.
Be aware that it may be necessary to re-tighten hitch hardware and/or wheel bolts; please refer to
Section 4 in this manual for the proper torque specifications.

Summary of Contents for 57G







































Reviews: