background image

4K 8x8 HDMI Matrix Switcher-N

 

26 

There is a blank screen on 
the display when switching 

The 

display 

does 

not 

support  the  resolution  of 
the video source. 

Switch again. 

Manage  the  EDID  data 
manually  to  make  the 
resolution  of  the  video 
source 

automatically 

compliant  with  the  output 
resolution. 

Cannot  control  the  device 
by  control  device  (e.g.  a 
PC) through RS232 port 

Wrong connection 

Check 

to 

ensure 

the 

connection  between  the 
control device and the unit 

Wrong RS232 
communication parameters 

Type in correct RS232 
communication 
parameters: Baud 
rate:9600; Data bit: 8; Stop 
bit: 1; Parity bit: none 

Broken RS232 port 

Send it to authorized 
dealer for checking. 

Static  becomes  stronger 
when  connecting  the  video 
connectors 

Bad grounding 

Check  the  grounding  and 
make  sure  it  is  connected 
well. 

Cannot  control  the  device 
by  RS232  /  IR  remote  / 
front panel buttons 

The device has already 
been broken. 

Send it to authorized 
dealer for repairing. 

If your problem persists after following the above troubleshooting steps, seek further 
help from authorized dealer or our technical support. 

Summary of Contents for MP-HD-88A-N

































Reviews: