Miles Industries HORIZON 535XAN Installation & Operating Instructions Manual Download Page 5

55

State of California. Proposition 65 Warning. 

Fuels used in gas, wood-burning or oil fired appliances, and the products 

of combustion of such fuels, contain chemicals known to the State of California to cause cancer, birth defects and other 

reproductive harm. California Health & Safety Code Sec. 25249.6.

State of Massachusetts Carbon Monoxide Detector/Vent Terminal Signage Requirements

For all side wall horizontally vented gas fueled equipment installed in every dwelling, building or structure used in whole or 

in part for residential purposes, including those owned or operated by the Commonwealth and where the side wall exhaust 

vent termination is less than seven (7) feet above finished grade in the area of the venting, including but not limited to 

decks and porches, the following requirements shall be satisfied: 

1. INSTALLATION OF CARBON MONOXIDE DETECTORS. At the time of installation of the side wall horizontal vented 

gas fueled equipment, the installing plumber or gas fitter shall observe that a hard wired carbon monoxide detector with 

an alarm and battery back-up is installed on the floor level where the gas equipment is to be installed. In addition, the 

installing plumber or gas fitter shall observe that a battery operated or hard wired carbon monoxide detector with an 

alarm is installed on each additional level of the dwelling, building or structure served by the side wall horizontal vented 

gas fueled equipment. It shall be the responsibility of the property owner to secure the services of qualified licensed 

professionals for the installation of hard wired carbon monoxide detectors.

a. In the event that the side wall horizontally vented gas fueled equipment is installed in a crawl space or an attic, the hard 

wired carbon monoxide detector with alarm and battery back-up may be installed on the next adjacent floor level.

b. In the event that the requirements of this subdivision can not be met at the time of completion of installation, the owner 

shall have a period of thirty (30) days to comply with the above requirements; provided, however, that during said thirty 

(30) day period, a battery operated carbon monoxide detector with an alarm shall be installed.

2. APPROVED CARBON MONOXIDE DETECTORS. Each carbon monoxide detector as required in accordance with the 

above provisions shall comply with NFPA 720 and be ANSI/UL 2034 listed and IAS certified. 

3. SIGNAGE. A metal or plastic identification plate shall be permanently mounted to the exterior of the building at a 

minimum height of eight (8) feet above grade directly in line with the exhaust vent terminal for the horizontally vented gas 

fueled heating appliance or equipment. The sign shall read, in print size no less than one-half (1/2) inch in size, “GAS 

VENT DIRECTLY BELOW. KEEP CLEAR OF ALL OBSTRUCTIONS”.

4. INSPECTION. The state or local gas inspector of the side wall horizontally vented gas fueled equipment shall not 

approve the installation unless, upon inspection, the inspector observes carbon monoxide detectors and signage installed 

in accordance with the provisions of 248 CMR 5.08(2)(a)1 through 4. 

(b) EXEMPTIONS: The following equipment is exempt from 248 CMR 5.08(2)(a)1 through 4: 

1. The equipment listed in Chapter 10 entitled “Equipment Not Required To Be Vented” in the most current edition of NFPA 

54 as adopted by the Board; and 

2. Product Approved side wall horizontally vented gas fueled equipment installed in a room or structure separate from the 

dwelling, building or structure used in whole or in part for residential purposes. 

(c) MANUFACTURER REQUIREMENTS - GAS EQUIPMENT VENTING SYSTEM PROVIDED. When the manufacturer 

of Product Approved side wall horizontally vented gas equipment provides a venting system design or venting system 

components with the equipment, the instructions provided by the manufacturer for installation of the equipment and the 

Safety and Warning Information

Summary of Contents for HORIZON 535XAN







































Reviews: