Miles Industries HORIZON 535XAN Installation & Operating Instructions Manual Download Page 1

4000309-14
© 2009, Miles Industries Ltd. All rights reserved.

H

ORIZON

WARNING: If the information in these 

instructions is not followed exactly, a fi re 

or explosion may result causing property 

damage, personal injury or loss of life.

WHAT TO DO IF YOU SMELL GAS

• Do not try to light the appliance.

• Do not touch any electrical switch; do not 

use any phone in your building.

• Immediately call your gas supplier from 

a neighbor’s phone. Follow the gas 

supplier’s instructions.

• If you cannot reach your gas supplier, call 

the fi re department.

This appliance is only for use with the type 

of gas indicated on the rating plate. This 

appliance is not convertible for use with 

other gases, unless a certifi ed kit is used.

This appliance is a domestic room-heating 

appliance. It must not be used for any other 

purposes such as drying clothes, etc.
This appliance is suitable for installation in a 

bedroom or bed sitting room.

Manufactured by

MILES INDUSTRIES LTD.

British Columbia, Canada

www.valorfi replaces.com

Installation & Operating Instructions

Do not store or use gasoline or other 

fl ammable vapors and liquids in the vicinity 

of this or any other appliance.

Installation and service must be performed 

by a qualifi ed installer, service agency or the 

gas supplier.

This appliance may be installed in an 

after-market permanently located, 

manufactured (mobile) home where not 

prohibited by local codes.

Model 535XAN (Natural Gas)

Model 535XAP (Propane)

Direct Vent Gas Fireplace Heater

INSTALLER: Leave this manual with the appliance.

CONSUMER: Retain this manual for future reference.

Massachusetts

: The piping and fi nal 

gas connection must be performed by a 

licensed plumber or gas fi tter in the State of 

Massachusetts. Also, see Carbon Monoxide 

Detector requirements under “Safety and 

Warning Information” on page 5.

Please read this manual BEFORE installing and operating this appliance.

Summary of Contents for HORIZON 535XAN







































Reviews: