Miele WWV 980 WPS Passion Operating Instructions Manual Download Page 105 | Manualshive

Page: 105 / 120

background image

Consumption data

105

Note for test institutes

*

Test programme in accordance with EN 60456 and energy label with

Directive 1061/2010

Consumption data can vary from the nominal values given depending on water
pressure, water hardness, water inlet temperature, room temperature, type and
volume of load, fluctuations in the electricity supply and any extras selected.

With the

PowerWash 2.0

washing technique, during the heating phase, the tem-

perature measured by the sensor in the suds container is higher than the actual
temperature of the laundry.
The temperature measured there

does not

reflect the temperature of the laun-

dry.

The consumption data shown in the EcoFeedback display can vary from the
consumption data quoted here. The variations arise from component tolerances
and on-site conditions e.g. fluctuations in the pressure of the water supply,
mains voltage and fluctuations in the mains voltage.

«
...
103
104
105
106
107
...
»

Summary of Contents for WWV 980 WPS Passion

























































































































Reviews:

No comments

Related manuals for WWV 980 WPS Passion

Brand: Caloric Pages: 12

Brand: Dacor Pages: 32

Brand: davoline Pages: 68

Brand: Maytag Pages: 88

Brand: Baumatic Pages: 28

Brand: NEFF Pages: 32

Brand: Campomatic Pages: 36

Brand: Pacific hydrostar Pages: 17

Brand: P&C Pages: 45

Brand: BOMANN Pages: 15

Brand: GE Pages: 20

IVC 60/12-1 Ec H Z22

Brand: Kärcher Pages: 372

Brand: FAR Pages: 155

Brand: mykin Pages: 2

EDF 100243 BlackLine

Brand: ECG Pages: 120

Brand: Haier Pages: 12

Brand: Haier Pages: 10

Brand: Haier Pages: 19

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands