Miele WWR 860 WPS Operating Instructions Manual Download Page 75

Page: 75 / 116

Problem solving guide

Fault messages at the end of a programme

Problem

Possible cause and remedy



Intensive flow: Clean
the filter and jet
nozzle or remove
foreign objects from
the pump housing

The pumps are dirty.



Clean the pumps as described in “Problem solving
guide - Opening the door in the event of a blocked
drain outlet and/or power cut”.



Restart the programme after cleaning.

The jet in the top of the door ring is blocked with fluff.



Remove the fluff with your finger. Do not use any
sharp or pointed tools to do this.



Restart the programme after cleaning.

If the fault message appears again, contact Miele.
The washing machine can still be used but with
reduced functionality.



Align the machine.
Laundry not properly
spun.

The

Pre-ironing

Extra which runs at the end of the

programme could not be carried out properly.



Check whether the washing machine is aligned
correctly as described in “Installation – Levelling
the machine”.



Check whether the maximum delivery height of
1 m has been exceeded.

If the fault message appears again, contact Miele.
The washing machine can still be used but with
reduced functionality.

The messages will appear at the end of the programme and when the washing
machine is switched on and need to be confirmed with the

sensor.

Summary of Contents for WWR 860 WPS





















































































































Search results

Summary of Contents for WWR 860 WPS

Reviews:

Related manuals for WWR 860 WPS

Brands by name

Popular brands

Miele WWR 860 WPS, Operating Instructions Manual

Search results

Summary of Contents for WWR 860 WPS

Reviews:

Related manuals for WWR 860 WPS

Brands by name

Popular brands