Miele WTD 160 Operating Instructions Manual Download Page 76 | Manualshive

Page: 76 / 100

background image

Installation

*INSTALLATION*

76

The water protection system

The Miele water protection system pro-
tects all parts of the washer-dryer from
water damage.

The system mainly consists of the fol-
lowing components:

- the inlet hose

- the electronic unit and drainage and

overflow protection

- the drain hose

Inlet hose

- Protected from bursting

The inlet hose can withstand pres-
sure of more than 7000 kPa.

Electronic unit and casing

- The floor tray

Any leaking water is collected in a
floor tray in the base of the washer-
dryer. A float switches off the water
inlet valves. Further water intake is
blocked. The water inside the suds
container is pumped down.

- Overflow protection

This prevents the washer-dryer from
taking in too much water and over-
flowing. If the water level exceeds a
certain level, the drain pump
switches on and pumps the excess
water away.

Drain hose

The drain hose is protected by a ventila-
tion system which prevents the washer-
dryer from being emptied completely.

«
...
74
75
76
77
78
...
»

Summary of Contents for WTD 160





































































































Reviews:

No comments

Related manuals for WTD 160

Millennia EDW24

Brand: Dacor Pages: 16

Brand: Gaggenau Pages: 76

Brand: Blanco Pages: 16

Brand: White-Westinghouse Pages: 16

Brand: Omega Pages: 6

Brand: GE Pages: 28

Brand: Parkside Pages: 33

Brand: Bush Pages: 25

Brand: Maytag Pages: 28

Brand: Andis Pages: 20

Brand: Daewoo Pages: 17

Brand: TdA electronics Pages: 12

DHP 8 A++ W205T

Brand: VALBERG Pages: 136

Brand: Hotpoint Pages: 12

Brand: Solt Pages: 2

Brand: Annovi Reverberi Pages: 9

Brand: Hotpoint Pages: 24

Brand: Smeg Pages: 42

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands