Miele WTD 160 Operating Instructions Manual Download Page 9

Page: 9 / 100

Warning and Safety instructions



Faulty components must only be replaced by genuine Miele ori-

ginal spare parts. Only when these parts are fitted can Miele guaran-
tee the safety standards of the machine.



If the electrical connection cable is faulty it must only be replaced

by a Miele authorised service technician to protect the user from
danger.



This washer-dryer must not be used in a non-stationary location

(e.g. on a ship).



Do not make any alterations to the washer-dryer, unless author-

ised to do so by Miele.



Reliable and safe operation of this washer-dryer can only be as-

sured if it has been connected to the mains electricity supply.



The manufacturer’s warranty will be invalidated if the washer-dryer

is not repaired by a service technician authorised by Miele.

Summary of Contents for WTD 160





































































































Search results

Summary of Contents for WTD 160

Reviews:

Related manuals for WTD 160

Brands by name

Popular brands

Miele WTD 160, Operating Instructions Manual

Search results

Summary of Contents for WTD 160

Reviews:

Related manuals for WTD 160

Brands by name

Popular brands