Miele W 2129 Operating Instructions Manual Download Page 11

Page: 11 / 68

Control panel

Start button

Starts the wash programme

Additional option buttons

Additional options can be added to
the basic programme.
Use the top button to select either
the

Intensive

Pre-wash

, or

Soak

option or a combination of these
options.
Use the lower button to select the

Water plus

option.

Indicator light on = option selected
Indicator light off = option not

selected

Indicator lights for spin speed,
Rinse hold or Without spin

Spin button

For selecting the final spin speed,

Rinse hold

Without spin

Programme selector

For selecting the wash programme
and temperature for that programme.
The programme selector can be
turned clockwise or anti-clockwise

Programme sequence indicator
lights

Show which section of the wash
programme has been reached

Check lights

I-On/0-Off button

For switching the machine on or off
or interrupting a programme

Door button

Opens the machine door

Description of the machine

Summary of Contents for W 2129





































































Search results

Summary of Contents for W 2129

Reviews:

Related manuals for W 2129

Brands by name

Popular brands

Miele W 2129, Operating Instructions Manual

Search results

Summary of Contents for W 2129

Reviews:

Related manuals for W 2129

Brands by name

Popular brands