Miele W 2104 Operating Instructions Manual Download Page 57

Page: 57 / 64

Follow steps

to programme

and store in memory.

Before you begin, first ensure that:

– The washing machine is switched off.

– The machine is properly closed.

– The programme selector is at

Finish

Press the

Start

button and keep it

pressed in whilst carrying out steps

Switch the machine on with the

I-On/0-Off

button.

Wait until the

Start

indicator light

comes on . . .

. . . and then release the

Start

button.

Turn the programme selector to the

Cottons 75°C

position:

The

Soak/Pre-wash

sequence indicator

light will briefly flash twice in 2 second
intervals, to show that factory Setting 2
is stored in memory.

Each subsequent press on the

Start

button selects a different setting (see
list on previous page).

The

Soak/Pre-wash

sequence indicator

light will flash:

–

x 1

= Setting 1

–

x 2

= Setting 2

–

x 3

= Setting 3

–

x 4

= Setting 4

Switch the machine off with the

I-On/0-Off

button.

The

Water plus

button has now been

allocated the setting you have chosen.
This setting will remain in memory until
another setting is programmed.

Programmable functions

Summary of Contents for W 2104

































































Search results

Summary of Contents for W 2104

Reviews:

Related manuals for W 2104

Brands by name

Popular brands

Miele W 2104, Operating Instructions Manual

Search results

Summary of Contents for W 2104

Reviews:

Related manuals for W 2104

Brands by name

Popular brands