Miele TMB540 WP Eco Operating Instructions Manual Download

Page: 64 / 80

Installation and connection

Refitting

7. Refit the door



Press the rubber seal back into the
grove on the door.



Position the door in front of the dryer.



Fit the base of the door hinge with its
2 pins into the openings on the dryer.

The base of the door hinge must be
flush with the front panel of the dryer.
The door cannot fall off in this position.



Screw the door securely to the dryer
at the base of door hinge



Now that you have changed the door
hinging the door will open from the
opposite side.



Push the orange marker round to the
other side so that you will see at
which side to pull the door open.

Important

Please keep the lock catch and door
hinge covers which were no longer
needed in a safe place. These will be
required if, for example, you move
house and need to change the door
hinging back to its original position.

Summary of Contents for TMB540 WP Eco

















































































Search results

Summary of Contents for TMB540 WP Eco

Reviews:

Related manuals for TMB540 WP Eco

Brands by name

Popular brands

Miele TMB540 WP Eco, Operating Instructions Manual

Search results

Summary of Contents for TMB540 WP Eco

Reviews:

Related manuals for TMB540 WP Eco

Brands by name

Popular brands