Miele TMB540 WP Eco Operating Instructions Manual Download

Page: 40 / 80

Fragrance flacon

Using a fragrance flacon (optional ac-
cessory) will add a pleasant fragrance
to your laundry.



Before using a fragrance flacon,

please read "Warning and safety in-
structions - Using a fragrance flacon
(optional accessory)".

Inserting a fragrance flacon

Only hold the fragrance flacon as il-
lustrated. Do not hold it at an angle
or tip it as the fragrance will leak out
of the flacon.



Hold the flacon securely to prevent
opening it by mistake.



Pull off the protective seal.



Open the door of the tumble dryer.

The fragrance flacon is inserted in the
upper fluff filter in the opening on the
right hand side beside the grip.

If you are not using a fragrance
flacon: the cover must always remain
closed (push the cover down com-
pletely with the tab).



Open the cover using the tab until the
tab is at the top right hand side as
shown.



Insert the flacon in the opening as far
as it will go.

Summary of Contents for TMB540 WP Eco

















































































Search results

Summary of Contents for TMB540 WP Eco

Reviews:

Related manuals for TMB540 WP Eco

Brands by name

Popular brands

Miele TMB540 WP Eco, Operating Instructions Manual

Search results

Summary of Contents for TMB540 WP Eco

Reviews:

Related manuals for TMB540 WP Eco

Brands by name

Popular brands