Miele T 8822 C Operating Instructions Manual Download Page 34

Page: 34 / 64

Problem

Possible cause

Remedy

The Clean out
airways indicator
light comes on.

The dryer is not working
efficiently or economically.
Possible cause: the filters
are clogged with fluff or with
detergent residues.

– Cleaning the filters is

usually all that is required.
However, if the reminder
does not go out after you
have cleaned the filters,
then also check all the
possible causes
described under "The
drying process goes on
too long or even switches
off".

To switch off this
reminder:

– Open and shut the door

with the dryer switched
on.

The

Clean out airways

indicator light can be
deactivated (see
"Programmable functions").

The programme
stops and
the Clean out
airways indicator
light comes on.
The buzzer
sounds.

See above for possible
causes and their remedies.

To switch off this warning:

– Open and shut the door

with the dryer switched
on.

– Then start the programme

again.

– If this problem happens

again, contact Miele.

The Empty
container indicator
light comes on.
The buzzer
sounds.

The condensed water
container is full or there is
kink in the drain hose.

– Empty out the condensed

water container.

– Check the drain hose.

To switch off this warning:

– Open and shut the door

with the dryer switched
on.

Problem solving guide

Summary of Contents for T 8822 C

































































Search results

Summary of Contents for T 8822 C

Reviews:

Related manuals for T 8822 C

Brands by name

Popular brands

Miele T 8822 C, Operating Instructions Manual

Search results

Summary of Contents for T 8822 C

Reviews:

Related manuals for T 8822 C

Brands by name

Popular brands