Miele T 8822 C Operating Instructions Manual Download

Page: 18 / 64

Select a programme

Select the programme you want.

The indicator for the programme
selected will light up.
A drying level or extra option indicator
may also light up and the duration may
also be displayed.

Drying level programmes

–

Cottons, Minimum iron, Delicates,
Proofing, Express, Automatic plus,
Denim, Shirts

Press the drying level button
repeatedly until the indicator for the
drying level you want lights up (for
almost all programmes).

Any of the four drying levels can be
selected for the

Cottons

and

Express

programmes. A more limited range is
available when using other

programmes and with some the drying
level is pre-set and cannot be changed.

Note

You can extend the range of the drying
levels for some programmes (see
"Programmable functions").

Woollens handcare, Gentle
smoothing

– This programme cannot be changed.

Selecting the duration of the timed
drying Cool air and Warm air
programmes

The indicator light for the

Delay start

button will flash when the

Cool air or

Warm air

programme is selected.

Press the

Delay start

button

repeatedly until the required duration
shows in the display.

You can select the duration in stages
for:

–

Cool air:

from

minutes up to

1:00

hour.

–

Warm air:

from

minutes up to

2:00

hours.

Select any Extra options / Delay

start

Low temperature, Buzzer

and

Delay

start

(see "Extra options/Delay start)"

are selected by pressing the
appropriate button.
Anti-crease (see next page) is
permanently switched on.

N.B.

: It is not possible to select

Delay

start

when using the

Warm air

Cool

air

programmes.

How to dry correctly

Summary of Contents for T 8822 C

































































Search results

Summary of Contents for T 8822 C

Reviews:

Related manuals for T 8822 C

Brands by name

Popular brands

Miele T 8822 C, Operating Instructions Manual

Search results

Summary of Contents for T 8822 C

Reviews:

Related manuals for T 8822 C

Brands by name

Popular brands