Miele T 8822 C Operating Instructions Manual Download Page 14

Page: 14 / 64

Control panel

Low temperature button

Delicate fabrics are dried at a lower
temperature.

Drying level button

with indicator lights to show the
drying level selected.

Display

See next page.

Delay start button

This button is used for:
- Delaying the start of a programme
- Selecting the duration of the timed

drying

Warm air

and

Cool air

programmes

Buzzer button

An audible tone sounds at the end of
the programme.

Perfect Dry indicator

For all programmes with a selectable
drying level. See next page.

Check lights

For a description of these, see "Pro-
blem solving guide" / "After sales ser-
vice".

Start/Stop button

For starting or cancelling a program-
me.
The button flashes while a program-
me is being selected and then lights
up constantly when the programme
has started.

Programme selector

with indicator lights to show the pro-
gramme selected.

Door button

Pressing this button will open the
door even when the dryer is
switched off at the mains.

On/Off button

For switching the dryer on and off.

Operating the tumble dryer

Summary of Contents for T 8822 C

































































Search results

Summary of Contents for T 8822 C

Reviews:

Brands by name

Popular brands

Miele T 8822 C, Operating Instructions Manual

Search results

Summary of Contents for T 8822 C

Reviews:

Brands by name

Popular brands