Miele T 8622 C Operating Instructions Manual Download Page 50

Page: 50 / 56

To open the Settings menu

Close the door.

Switch the dryer on.

Press both menu buttons at the same
time until the following appears in the
display:

Settings

Language

Continue

You are now in the

Settings

menu.

Select the setting you want with the left
hand

button under

Continue

and confirm your selection with the right
hand

button under

To close the Settings menu

Settings

Back

Continue

Press the right hand

button

under

Language

The display can be set to appear in
one of several different languages.

Select the language you want by
pressing the left hand

button

under

(Continue).

A tick

will appear beside the

language to show that it has been set.

The flag

after the word

Language

acts as a guide to prevent a language
which will not be understood from
being set.

Settings menu

Summary of Contents for T 8622 C

























































Search results

Summary of Contents for T 8622 C

Reviews:

Brands by name

Popular brands

Miele T 8622 C, Operating Instructions Manual

Search results

Summary of Contents for T 8622 C

Reviews:

Brands by name

Popular brands